Viessmann Vitotronic 100 GC1 Скачать руководство пользователя страница 87

Страница: 87 / 132

Start-up

Steps

(continued)

3. Integrate the control unit in the LON BUS system

Single-boiler system only

The LON communication module
(accessory) must be inserted
(see page 111).

Set the LON participant number

Set the LON participant number via
coding address ”77” in coding 1
(factory setting: ”77: 1”).

See page 115 for coding 1.

Please note:

The same number must

not

assigned twice within a LON BUS
system.

Update the LON participant list

This is only possible when all participants are connected and the control unit is
coded as the error manager (coding ”79: 1”).

Press

and

simultaneously for

approx. 2 seconds.

Press

The participant check is initiated
(see also page 88).

The participant list is updated after
approx. 2 minutes.
The participant check is terminated.

Example of single-boiler system with Vitotronic 050 heating circuit controls and Vitocom connected downstream

Participant No. 1
Coding ”77: 1”

Participant No. 10
Coding ”77: 10”

Participant No. 11
Set coding ”77: 11”

Participant No. 100

Control unit is error
manager
Coding ”79: 1”

Control unit is not error
manager
Coding ”79: 0”

Unit is error manager

–––

Transmit time via LON
Set coding ”7b: 1”

Time is received via LON
Set coding ”81: 3”

Time is received via LON

–––

Transmit outdoor
temperature via LON
Set coding ”97: 2”

Outdoor temperature is
received via LON
Set coding ”97: 1”

–––

1 2 3 4 5 6 7

Vitotronic 100

Vitotronic 050

Vitocom

LON

Содержание Vitotronic 100 GC1





































































































































Результаты поиска

Содержание Vitotronic 100 GC1

Отзывы:

Viessmann Vitotronic 100 GC1, Инструкция по установке и обслуживанию, Страница: 87 / 132

Результаты поиска

Содержание Vitotronic 100 GC1

Отзывы: