Viessmann Vitotronic 100 GC1 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 132

Viessmann Vitotronic 100 GC1 Скачать руководство пользователя страница 39

Installation

39

Control and Junction Box Installation Instructions (for CM2 only)

1. Route cables and capillaries from

control through the opening in the
control panel. Guide the cables to
the junction box through the
opening in the rear panel and along
the top rail to the control. Secure
all cables to the rail with cable ties.
Insert capillaries into the sensor well.

Note:

Never allow cables to come

in contact with hot metal
components.

2. Mount the control to the control

panel.

3. Secure the control to the control

panel with screws.

Note:

Screws to secure control are

included with the cosmetic
cover in the boiler jacketing
package.

4. Install the junction box to the rear

panel either right or left. Secure the
junction box with 4 x 4.8 metal
screws.

Note:

The ground screw and ground

wire can be removed and then
reinstalled with the boiler back
panel attached.

5

3

5

1

3

3

8

v

1

.8

Do not bend or kink the capillaries.
Damaging the capillaries leads to
malfunction.

WARNING

«
...
37
38
39
40
41
...
»

Содержание Vitotronic 100 GC1





































































































































Отзывы:

Нет отзывов