Viessmann Vitotronic 100 GC1 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 132

Viessmann Vitotronic 100 GC1 Скачать руководство пользователя страница 2

General information

2

Safety, Installation and Warranty Requirement

Please ensure that this manual is read and understood before commencing installation. Failure to comply

with the issues

listed below and details printed in this manual can cause

product/property damage, severe personal injury,

and/or

loss of

life

. Ensure all requirements below are understood and fulfilled (including detailed information found in manual subsections).

Licensed professional heating
contractor

The installation, adjustment, service,
and maintenance of this equipment

must be

performed by a licensed

professional heating contractor.

Please see section

entitled “Important
Regulatory and
Installation
Requirements.”

Product documentation

Read all applicable documentation

before commencing installation. Store
documentation near boiler in a readily
accessible location for reference in the
future by service personnel.

For a listing of

applicable literature,
please see section
entitled “Important
Regulatory and
Installation Requirements.”

Advice to owner

Once the installation work is complete,
the heating contractor must familiarize
the system operator/ultimate owner
with all equipment, as well as safety
precautions/requirements, shut-down
procedure, and the need for
professional service annually before the
heating season begins.

Warranty

Information contained in
this and related product
documentation must be
read and followed.

Failure

to do so renders warranty
null and void.

5

3

5

1

3

3

8

v

1

.8

«
1
2
3
4
...
»

Содержание Vitotronic 100 GC1





































































































































Отзывы:

Нет отзывов