Viessmann Vitotronic 100 GC1 Скачать руководство пользователя страница 122

Страница: 122 / 132

Additional information

122

Coding 2

(continued)

Overview of all codings

(continued)

Coding as per
factory setting
Address: Value

Function

New coding
Address:
Value

Possible change

55: 0

DHW

Tank heating,
differ/- 2.5°C / 4.5°F

55: 1

Adaptive tank heating active
(takes into account the rate at
which the tank temperature
increases during domestic hot
water heating)

55: 2

Tank temperature control with 2
tank temperature sensors

55: 3

DHW heating circuit temperature
control (sensor 17B if used in
conjunction with mixing valve and
a plate heat exchanger)

56: 0

DHW

Setting range of domestic hot water tem-
perature 10 to 60°C / 50 to 140°F

56: 1

Setting range of domestic hot
water temperature 10 to 95°C /
50 to 203°F

IMPORTANT

Observe max. DHW temperature

Adjust adjustable high limit ”

”

58: 0

DHW

Without additional function for domestic
hot water heating

58: 1
to
58: 95

nput of a 2nd set-point DHW

temperature value; variable between
1 and 95°C / 34 and 203

°F

(note

coding address ”56”).

CAUTION

Set the adjustable high limit ”

”

to a value which is at least 10

°C/

°F

higher than the maximum

domestic hot water temperature
( the temperature which is reached
by activating the additional function)

The temperature set on the

adjustable high limit ”

” must not

exceed the maximum permissible
tank temperature

See installation
instructions for the DHW
tank concerned

59: 0

DHW

Tank heating:
Switch-on point – 2.5°C / 4.5°F
Switch-off point + 2.5°C / 4.5°F

59: 1
to
59: 10

Switch-on point variable between 1
and 10°C / 18°F below set point
value

5A: 0

DHW

Without function

5A: 1

Supply temperature request of DHW tank

is the maximum value of the system

60: 20

DHW

When domestic hot water is being
heated, the boiler water temperature is a
maximum of 20°C / 36°F higher than the
set-point domestic hot water temperature

60: 10
to
60: 50

Differential between boiler water
temperature and set-point DHW
temperature adjustable between 10
and 50°C / 18 and 90°F

61: 1

DHW

Circulation pump switches on
immediately

61: 0

The circulation pump is switched
on as a function of the boiler
temperature

Содержание Vitotronic 100 GC1





































































































































Результаты поиска

Содержание Vitotronic 100 GC1

Отзывы:

Viessmann Vitotronic 100 GC1, Инструкция по установке и обслуживанию, Страница: 122 / 132

Результаты поиска

Содержание Vitotronic 100 GC1

Отзывы: