Viessmann Vitotronic 100 GC1 Скачать руководство пользователя страница 47

Страница: 47 / 132

Installation

Setting of the Fixed High Limit

(if required)

Settings on the control unit

The setting for the fixed high limit and
the other settings are dependent on the
safety equipment installed in
accordance with applicable codes.

The fixed high limit is supplied with
a factory setting of 110°C / 230°F.

- On Vitotronic 100, GC1 for

Vitorond 200, VD2 of
110°C / 230°F

- Adjustment to 99°C / 210°F

- On Vitotronic 100, GC1 for

Vitocrossal 300, CT3
Vitocrossal 200, CM2
of 99°C / 210°F
No adjustment

Disconnect power to control and
burner!

Unclip the fuse box and swing
upwards.

Turn the slotted screw on the rear
of the fixed high limit until the slot
points to 99°C / 210°F (once
adjusted, the fixed high limit

cannot

be reset to 110°C / 230°F).

Re-fit the fuse box.

Non-condensing boiler
(VD2/VD2A)

C /

Condensing boiler
(CT3)

C /

Condensing boiler
(CM2)

C /

Fixed high limit

110 / 230

99 / 210

Adjustable high limit

100 / 212

95 / 203

Coding for the electronic maximum
temperature limiter of Vitotronic 100;
set code 06 to the temperature as
shown or less

93 / 200

87 / 188

88 / 190

Содержание Vitotronic 100 GC1





































































































































Результаты поиска

Содержание Vitotronic 100 GC1

Отзывы:

Viessmann Vitotronic 100 GC1, Инструкция по установке и обслуживанию, Страница: 47 / 132

Результаты поиска

Содержание Vitotronic 100 GC1

Отзывы: