manualshive.com logo in svg

Victaulic VicFlex AB12, Руководство по монтажу на месте


Поделиться
Скачать
background image

I-VICFLEX_3

TABLE OF CONTENTS REV_A

Table of Contents

GENERAL 
INFORMATION ....................................................................... 11

Hazard Identification ...................................................................12
Introduction .................................................................................12

CONSTRUCTION REQUIREMENTS ........................................... 17
STYLES AB1, AB2, AND AB10 BRACKETS ............................... 21

Introduction .................................................................................22
Style AB1 Bracket Assembly Drawing ..........................................22
Style AB2 Bracket Assembly Drawing ..........................................23
Style AB10 Bracket Assembly Drawing ........................................24
Installation of Style AB1, AB2, and AB10 Brackets for ASTM 
635 Ceiling Suspension Systems in Accordance with ASTM 636 
Standards ....................................................................................24
Installation of the Style AB2 Bracket for ASTM C645 Hat Furring 
Channel Ceiling Systems Installed in Accordance with ASTM C754 
Standards (FM and VdS only) ......................................................26
Wood Joists/Studs Installation 
(FM Only for AB1 and FM/UL for AB2) ........................................28
ASTM C645 Metal Joists/Studs in Accordance with ASTM C754 
Standards Installation (FM Only for AB1 and 
FM/UL for AB2) ...........................................................................29
Alternative #1 – Wood Joist/Stud Installation  
(FM Only for AB1 and AB2) .........................................................30
Alternative #1 – Metal Joist/Stud Installation  
(FM Only for AB1 and AB2) .........................................................31
Alternative #2 – Wood Joist/Stud Installation  
(FM Only for AB1 and AB2) .........................................................32
Alternative #2 – Metal Joist/Stud Installation  
(FM Only for AB1 and AB2) .........................................................33

STYLE AB3 BRACKET ............................................................ 35

Introduction .................................................................................36
Style AB3 Bracket Assembly Drawing ..........................................36
Installation of the Style AB3 Surface-Mount Bracket on a Wall or 
Ceiling .........................................................................................37

Содержание VicFlex AB12













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VicFlex AB12

T-Drill F-400 Instruction Manual preview
F-400
Бренд: T-Drill Страницы: 75
Zeiss KS Instructions For Use Manual preview
KS
Бренд: Zeiss Страницы: 38
Campbell CS500 Instruction Manual preview
CS500
Бренд: Campbell Страницы: 18
Vector 0 Owner'S Manual & Warranty Information preview
0
Бренд: Vector Страницы: 4
National Instruments 9403 Getting Started Manual preview
9403
Бренд: National Instruments Страницы: 16
Jasco PRO Series Setup preview
PRO Series
Бренд: Jasco Страницы: 11
MacDon R216 Quick Card preview
R216
Бренд: MacDon Страницы: 2
MacDon R216 Operator'S Manual preview
R216
Бренд: MacDon Страницы: 214
MacDon R216 Installation Instructions Manual preview
R216
Бренд: MacDon Страницы: 32
4iiii FLiiiight Owner'S Manual preview
FLiiiight
Бренд: 4iiii Страницы: 36
4iiii FLiiiight User Manual preview
FLiiiight
Бренд: 4iiii Страницы: 34
4EVAC IMPACT Reference Manual preview
IMPACT
Бренд: 4EVAC Страницы: 27
Harken 3294 Instructions preview
3294
Бренд: Harken Страницы: 4
JBM 54172 Instruction Manual preview
54172
Бренд: JBM Страницы: 13
Rigol RP1010H User Manual preview
RP1010H
Бренд: Rigol Страницы: 12
CombiSteel 7455.17 Series User Manua preview
7455.17 Series
Бренд: CombiSteel Страницы: 60
Lightolier QVS2GPTLG232 Installation preview
QVS2GPTLG232
Бренд: Lightolier Страницы: 2
Fillauer ALP Aluminum Product Manual preview
ALP Aluminum
Бренд: Fillauer Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды