Victaulic VicFlex AB12 Скачать руководство пользователя

Страница: 101 / 204

I-VICFLEX_101

STYLE AQD-M BRACKET INSTALLATION
FOR ROUND OR SQUARE METAL
OR FRP DUCTS REV_A

Apply duct mastic/sealant to the duct

around the drilled hole as shown in the
picture to the left. Always refer to the duct
mastic/sealant manufacturer’s instructions.

Place the bracket onto the duct.

. Verify that the bracket opening is

aligned with the hole in the duct.

4a.

Install a

3/16

” stainless steel, domed-head, sealing blind rivet (recommended) into

each drilled hole.

NOTE

: Hardware is not included and shall be stainless steel or a

material suitable for the application.

4b.

Four stainless steel #10 Type AB self-tapping metal screws can be used instead

of rivets. When using self-tapping sheet metal screws, holes do not have to be drilled
into the duct.

NOTE

: Hardware is not included and shall be stainless steel or a material

suitable for the application.

Using a rivet squeezer tool, install the four rivets.

Содержание VicFlex AB12













































































































































































































Результаты поиска

Содержание VicFlex AB12

Отзывы:

Похожие инструкции для VicFlex AB12

Бренды по названию

Популярные бренды

Victaulic VicFlex AB12, Руководство по монтажу на месте

Результаты поиска

Содержание VicFlex AB12

Отзывы:

Похожие инструкции для VicFlex AB12

Бренды по названию

Популярные бренды