Victaulic VE268 Скачать руководство пользователя страница 8

Страница: 8 / 64

TOOL NOMENCLATURE

NOTICE

• Drawings and/or pictures in this manual may be exaggerated for clarity.
• The tool, along with this operating and maintenance instructions manual, contains

trademarks, copyrights, and/or patented features that are the exclusive property of
Victaulic.

Hydraulic Cylinder

Pipe Size Indicator
Depth Adjuster

Depth Adjuster Lock

Upper Roll Assembly
Upper Roll Bolt

Selector Valve

Lower Roll

Stabilizer

Assembly

Stabilizer

Handwheel

Safety Foot

Switch

Roll Guards

Guard Setting

Pad

Jog Switch

On/Off Switch

Grooving rolls can crush or cut fingers

and hands.

• Always disconnect the tool from the power

source before making any tool adjustments.

• Make sure the guard is adjusted properly

before grooving pipe.

• Loading/unloading pipe will place your

hands close to the grooving rolls. Keep

hands away from the grooving rolls and the

roller on the pipe stabilizer during operation.

• Never reach inside the pipe ends or across

the tool or pipe during operation.

• Never groove pipe that is shorter than the

recommended lengths listed in the

operating and maintenance manual.

• Never wear loose clothing, loose gloves, or

anything that can become entangled in

moving parts.

2244 Rev. D

R007276LBL

ALWAYS KEEP THIS PAD WITH THE TOOL.

USE IT TO SET THE GUARDS IN ACCORDANCE

WITH THE TOOL OPERATION AND

MAINTENANCE MANUAL.

4868 Rev. D

R068272LAB

Contact with hazardous voltage

inside this door may result in death

or serious personal injury.

• ALWAYS disconnect the tool from

the power source before performing

maintenance or adjustments.

• Only qualified personnel should

open this door.

5038 Rev. B

R090424LAB

Failure to follow instructions and warnings could result in

serious personal injury, property damage, and/or product

damage.

• Before operating or servicing any pipe preparation tools,

read all instructions in the Operating and Maintenance

Instructions Manual and all labels on the tool.
• Wear safety glasses, hardhat, foot protection, and hearing

protection when working around tools.

0567 Rev. D

R031272LAB

If you need additional copies of any literature, or if you have questions concerning the safe and proper

operation of any pipe preparation tools, contact Victaulic, P.O. Box 31, Easton, PA 18044-0031, Phone

1-800-PICK VIC, E-Mail: [email protected].

Emergency Stop

TM-VE268_8

REV_H

TM-VE268

/ Operating and Maintenance Instructions Manual

Содержание VE268

































































Результаты поиска

Содержание VE268

Отзывы:

Похожие инструкции для VE268

Бренды по названию

Популярные бренды

Victaulic VE268, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание VE268

Отзывы:

Похожие инструкции для VE268

Бренды по названию

Популярные бренды