Victaulic TM-PFT510 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 25

Victaulic TM-PFT510 Скачать руководство пользователя страница 13

PRESSING OPERATION FOR

1/2-INCH/21.3-MM, 3/4-INCH/

26.9-MM, AND 1-INCH/33.7-MM

SIZES

WARNING

•

Before operating the PFT510 Vic-Press
Schedule 10S Tool, read the I-P500 Field
Installation Handbook, and follow all
instructions in the previous sections of
this manual.

•

Wear hardhat, safety glasses, foot
protection, and hearing protection.

•

The PFT510 Vic-Press Schedule 10S Tool
is designed for use ONLY with Vic-Press
Schedule 10S System Products. Refer
to the “Introduction” section. DO NOT
attempt to install Schedule 5 Pressfit
Products with this tool.

•

The proper size standard Vic-Press jaw
must be used for the fitting and pipe size
being installed.

•

Inspect the tool and standard Vic-Press
jaw for loose, broken, or damaged parts
before attempting to perform the pressing
operation.

•

DO NOT ALTER THE PFT510 VIC-
PRESS SCHEDULE 10S TOOL OR JAWS
IN ANY WAY. ALTERATIONS TO ANY
TOOL COMPONENTS MAY RESULT IN
IMPROPER PRODUCT INSTALLATION
AND WILL VOID THE VICTAULIC
WARRANTY.

•

Keep fingers and hands away from
all pinch points during the pressing
operation.

Failure to follow these instructions could
result in serious personal injury, property
damage, and joint failure.

1 . Check the standard Vic-Press jaw for
damage or wear before performing the pressing
operation . Replace any damaged or worn
standard Vic-Press jaws .

2 . Open the standard Vic-Press jaw by
squeezing the levers .

Pipe Side Locator

of Standard

Vic-Press Jaw

3 . Position the standard Vic-Press jaw over the
Vic-Press Schedule 10S fitting . Make sure the
standard Vic-Press jaw cavity aligns with the
seal pocket bead of the fitting . The “pipe side”
locator of the standard Vic-Press jaw must
be positioned over the pipe, as shown above .

NOTE:

Always position the tool/standard Vic-

Press jaw onto the fitting at a right angle to the
pipe axis .

DO NOT ATTEMPT TO REMOVE THE

“PIPE SIDE” LOCATOR FROM THE STANDARD

VIC-PRESS JAW. ALTERATIONS TO ANY TOOL

COMPONENTS MAY RESULT IN IMPROPER

PRODUCT INSTALLATION AND WILL VOID
THE VICTAULIC WARRANTY.

3a . Release the levers to allow the standard Vic-
Press jaw to close around the fitting .

TM-PFT510_12

TM-PFT510

OPERATING AND MAINTENANCE INSTRUCTIONS MANUAL

www.victaulic.com

VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.

REV_D

«
...
11
12
13
14
15
...
»

Содержание TM-PFT510


























Отзывы:

Нет отзывов