manualshive.com logo in svg

Vetland EX3000, Руководство оператора

Поделиться
Скачать
Vetland EX3000 Скачать руководство пользователя страница 48

6-6

Troubleshooting

Alarm Matrix

Table 6-2 contains alarms that may occur during operation of your EX3000 Anesthesia System and their
possible causes and solutions. If the alarm continues to display after trying the suggested corrective
actions, please contact Vetland or your local dealer.

Table 6-2 EX3000 Anesthesia System Alarm Matrix

Alarm Message

Cause

Solution

Add Agent

Anesthetic agent level

in vaporizer is low.

1. Remove the anesthetic agent filler plug.
2. Fill the vaporizer with the appropriate anesthetic

agent.

3. Reinstall the filler plug hand tight.

Apnea

Breath has not been
detected within the
alarm timing
thresholds

Check patient respiration

or

Turn apnea alarm off

or

Adjust breath detection time in system setup menu.

Flow Error

a. Low oxygen supply

Increase oxygen supply pressure to the anesthesia
system. Pressure must be maintained at 50-60 psi.

b. Internal fault

Contact Vetland or your local dealer for service.

High Pressure

Pressure exceeded
the high pressure
threshold setting

1. Verify that the inspiration and expiration valves move

freely.

2. Verify that pop-off valve is partially open.
3. Adjust the high pressure alarm setting.

Continuing Pressure

Pressure did not
return to the baseline

Same as for High Pressure alarm.

ISO/SEVO Agent
High Output

Anesthetic agent

percentage exceeded
the alarm threshold

Adjust the agent percentage alarm threshold or reduce
the anesthetic settings.

Low Battery

a. The anesthesia

system is not
plugged in to a live
AC power supply

Plug in the anesthesia system and supply AC power.

Note:

Full charge takes approximately 16 hours.

b. Battery is failing

Contact Vetland or your local dealer for service to
replace battery.

Note:

Battery should be replaced every three years.

Negative Pressure

System has detected

a negative pressure

1. Verify proper fresh gas flow.
2. Verify that the inspiration and expiration valves move

freely.

Out of Range

Oxygen flow rate and
anesthetic agent
percentage cannot be
maintained

Using the touch screen, reduce oxygen flow rate.
Using the touch screen, reduce anesthetic agent
percentage.

Содержание EX3000

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды