Vetland EX3000 Скачать руководство пользователя страница 46

Страница: 46 / 88

6-4

Troubleshooting

Table 6-1 EX3000 Anesthesia System Problem – Solution Matrix (continued)

No.

Problem

Cause

Solution

No gas flow

a. Facility or cylinder

gas supply valve
is closed

Open gas supply valve.

b. Gas cylinder is

empty

Replace empty gas cylinder.

c. Gas supply hose

is disconnected

1. Ensure gas supply hose is connected to the

cylinder or facility gas system.

2. Ensure the gas supply hose DISS connector is

securely connected to the anesthesia system.

d. Oxygen flow

control turned off

1. Press the green circle at the bottom of the O

flowmeter (Figure 1-5, 6) on the touch screen.

2. Press

until the desired flow rate is displayed.

e. Gas supply

regulator
malfunction

Connect the EX3000 to an alternate oxygen supply

Gas flow is not
sufficient

a. Oxygen flow is set

too low

1. Press the green circle at the bottom of the O

flowmeter on the touch screen.

2. Press

until the desired flow rate is displayed.

b. Leak around

vaporizer filler
ports.

1. Verify that the filler plug is completely screwed

into the filler port forming a tight seal.

2. Verify that filler plug o-ring is not damaged.

Replace if damaged.

3. Verify that filler plug o-ring is not obstructed by

animal hair, etc.

c. Leak in patient

breathing circuit

1. Check all hose connections, particularly around

mask or endotracheal tube.

2. Perform a System Pressure Leak Test as

specified below.

d. C0

absorber

canister is leaking

1. Remove the absorber canister
2. Remove any absorbent granules that are

lodged between the canister and sealing
gasket.

3. Reinstall the absorber canister.

Oxygen flush button
sticks

Malfunctioning flush
valve

The flush valve requires cleaning or replacement.
Contact Vetland or local dealer for service.

Oxygen flow failure

Internal fault

Contact Vetland or your local dealer for service.

Touch screen
displays but is
inactive

Internal fault

1. Reset the anesthesia system by turning the

power switch OFF (

) and then turn ON (

)

again.

2. If still inactive, contact Vetland or your local

dealer for service.

Audible leakage
around oxygen hose
connector

a. Loose oxygen

hose connection

Tighten the connection with a crescent wrench.

b. Damaged oxygen

DISS inlet fitting

Inlet must be replaced. Contact Vetland or your
local dealer for service.

Содержание EX3000

























































































Результаты поиска

Содержание EX3000

Отзывы:

Бренды по названию

Популярные бренды

Vetland EX3000, Руководство оператора

Результаты поиска

Содержание EX3000

Отзывы:

Бренды по названию

Популярные бренды