Vetland EX3000 Скачать руководство пользователя страница 31

Страница: 31 / 88

System Setup

4-3

Filling the Anesthetic Vaporizers – Funnel Fill

1. Clean any hair or debris from around the filler port with a clean cloth.

2. Place a clean cloth beneath the anesthetic filler port.

3. Remove the filler plug for the appropriate (Isoflurane or Sevoflurane) anesthetic vaporizer filler

port (see Figure 4-2) by turning counterclockwise.

4. Carefully pour the appropriate agent into the filler port using a filler tube or funnel.

WARNING!

Make sure to pour the correct anesthetic into the filler port.

Filling with the

incorrect anesthetic agent could cause serious injury or death to the patient.

CAUTION!

If anesthetic agent spills on system surfaces, allow it to evaporate.

Rubbing

spilled anesthetic agent with a cloth may damage the system finish.

5. Observe the agent level indicator on the system display. Stop filling when the indicator bar reaches

the top of the indicator (see Figure 4-2).

6. Replace the filler plug and tighten by turning clockwise until hand tight.

Figure 4-2 Filling the Vaporizer – Funnel Fill

Use Only

Isoflurane

Use Only

Sevoflurane

–

Isoflurane

Level

Indicator

Sevoflurane
Level
Indicator

Pour

Isoflurane

Here

Содержание EX3000

























































































Результаты поиска

Содержание EX3000

Отзывы:

Бренды по названию

Популярные бренды

Vetland EX3000, Руководство оператора

Результаты поиска

Содержание EX3000

Отзывы:

Бренды по названию

Популярные бренды