background image

Vertical SUMMIT IP 

Hardware Description and Installation Manual

 

Issue 1.2 

 

 

Item 

Contents 

Batteries remplaçables 

« ATTENTION : risque d'explosion si la batterie est remplacée 
par un type de batterie incorrect. Mettez les batteries au rebut 
conformément aux instructions.» 

Courants de fuite dus à la 
tension de sonnerie - 
Marquage de l'installation 
de mise à la terre 

« COURANT DE FUITE ÉLEVÉ - Raccordez un conducteur 
permanent de mise à la terre avant de brancher des lignes 
téléphoniques.» 

Courants de fuite dus la 
tension de sonnerie - 
Instructions d'installation 
de mise à la terre 

« 1. Un conducteur de mise à la terre supplémentaire de 
l'équipement doit être installé entre le produit ou le système et 
la terre, c'est-à-dire, en plus du conducteur de mise à la terre de 
l'équipement dans le cordon d'alimentation. 
2. Le conducteur de mise à la terre supplémentaire de 
l'équipement doit être d'une taille inférieure aux conducteurs 
d'alimentation du circuit de dérivation non mis à la terre. Le 
conducteur de mise à la terre supplémentaire de l'équipement 
doit être raccordé au produit sur la borne appropriée et raccordé 
à la terre de manière à ce que la connexion de mise à la terre 
demeure en place lorsque le cordon d'alimentation est 
débranché. La mise à la terre du conducteur de mise à la terre 
supplémentaire de l'équipement doit être conforme aux règles 
appropriées pour les connecteurs terminaux de la section K de 
l'article 250 du Code national de l'électricité, ANSI/NFPA 70 et 
de l'article 10 de la section 1 du Code canadien de l'électricité, 
section 1, C22. Le raccordement du conducteur de mise à la 
terre supplémentaire peut être effectué sur l'acier d'une 
construction, sur un système de chemins de câbles électriques 
métalliques ou sur tout élément mis à la terre raccordé de 
manière permanente et fiable à l'équipement de service 
électrique mis à la terre. 
3. Des conducteurs de mise à la terre nus, couverts ou isolés 
sont acceptables. Un conducteur couvert ou isolé doit posséder 
une finition extérieure continue de couleur verte ou de couleur 
verte avec une ou plusieurs bandes jaunes.» 

Cordon de ligne 
téléphonique 

« ATTENTION : Afin de réduire les risques d'incendie, utilisez 
uniquement du cordon pour ligne de télécommunication certifié 
No. 26 AWG ou plus grand (par ex, 24 AWG) répertorié par l'UL 
ou la CSA. » 

Séparation des Tensions 
des réseaux de 
télécommunication (TNV) 
et Tensions de sécurité 
extra basses (SELV) - 
Enfichable A. 

« La prise de mise à la terre de protection distincte fournie sur 
ce produit doit être raccordée de manière permanente à la terre. 
» ou similaire (Instructions) 

 

 

 

 

 

Содержание SUMMIT IP








































































































Отзывы: