manualshive.com logo in svg

Vermeer 504 PRO, Руководство оператора и по техническому обслуживанию

Поделиться
Скачать
Vermeer 504 PRO Скачать руководство пользователя страница 64

504PRO_604PRO_o-m2_00

-

504/604 PRO Baler

Preparing the Equipment Baler 7-1

7 PREPARING THE EQUIPMENT BALER

WARNING:

Crushing can occur! During handling in the area of the drawbar ensure that the machine is secured against

moving. Do not raise the tongue jack before the baler has been safely coupled to the tractor.

Do not uncouple the baler, unless:

•

Baler is parked on solid, level ground

•

The baling chamber is empty and the tailgate closed

•

The wheels of the machine are blocked to prevent unexpected movement

•

Hydraulic system has been depressurized

•

The hitch is without load.

Nobody must be between tractor and baler unless wheels of both machines are blocked to prevent unexpected movement!

Always keep children away from the machine!

Always follow Shutdown Procedure before performing maintenance or repair work (see page 6-1)

WARNING:

Tailgate and ejected bale can crush. Proceed with particular care when opening and closing the tailgate. No

persons may stay in the swiveling range of the tailgate and in the bale unloading area.

In case of locations on a slope: Never eject a bale where it can roll. A rolling bale can be destructive and result in serious injury or death. Never try
to stop a rolling bale.

7.1

Install or Remove the Tongue Jack

Depending on the position of the crank handle in the support foot holder (pulled out or pushed in) the tongue jack moves fast or slow when you
turn the crank handle. The direction of movement when turning clockwise or counter clockwise is depending on the position of the crank handle
in the tongue jack holder (out or in).

•

To move the tongue jack quick, you must pull the crank handle out of the tongue jack up to the stop

•

Up: Turn the crank handle clockwise.

•

Down: Turn the crank handle counter clockwise.

https://tractormanualz.com

Содержание 504 PRO


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды