Vermeer 504 PRO Скачать руководство пользователя страница 127

Страница: 127 / 153

504PRO_604PRO_o-m2_00

504/604 PRO Baler

Maintenance/Setting 11-11

11.7

Chain Lubrication System Maintenance

11.7.1

Check the Level in the Oil Container of the Chain Lubrication

The chain lubrication system supplies oil from the container to the drive chains. Check the level in the oil container daily. Do not leak oil.

CAUTION:

Damage to the lubrication pump and roller chains can occur when the system runs without oil. Never let the oil

container run completely empty.

CAUTION:

Damage to the lubrication pump, roller chains and baler when the system runs with the wrong oil flow.Never

change the flow rate of the lubrication pump that was set in the factory. If adjustment is required, only a trained service
technician is allowed to make the change on the basis of the service information provided by Vermeer.

Procedure

1. Make sure the PTO shaft is switched off, tractor engine is stopped and the key is removed.

2. Check the level in the oil reservoir (2) .If necessary fill the oil container.

11.7.2

Fill the Oil Container

Requirements

•

Oil: SAE 30 motor oil or equivalent.

Procedure

1. Make sure the PTO shaft is switched off, tractor engine is stopped and the key is removed.

2. Clean the surroundings of the oil container (2) (see Figure 73 on page 11-12), this prevents that dirt falls in the container when you open it.

3. Remove the container cap (1).

4. Make sure the filter is clean, if necessary:

1. Remove the filter from the oil container.

2. Clean the filter and use exclusively petroleum-benzine or petroleum.

3. Insert the filter in the oil container.

5. Pour the new and clean oil through the filter and fill the oil container up to the marked maximum.

6. Put the container cap on the container.

https://tractormanualz.com

Содержание 504 PRO


























































































































































Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды

Vermeer 504 PRO, Руководство оператора и по техническому обслуживанию

Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды