Vermeer 504 PRO Скачать руководство пользователя страница 117

Страница: 117 / 153

504PRO_604PRO_o-m2_00

504/604 PRO Baler

Maintenance/Setting 11-1

MAINTENANCE/SETTING

WARNING:

Use Shutdown Procedure before servicing, cleaning, repairing or transporting machine (see page 6-1).

11.1

Tires on Baler

WARNING:

Tire explosion can result if the following procedures are not followed:

•

Maintain correct tire pressure. Do not inflate tire above recommended pressure (see page 11-3).

•

Low tire pressure can cause internal tire damage. Inflate to recommended pressure.

•

Replace any tires with cuts or bubbles. Replace any damaged rims.

•

Do not weld or heat wheel assembly. Heating will increase tire pressure.

•

Check tires and rims for damage (see page 11-3).

•

Check tires for correct pressure (see Figure 67 on page 11-2).

•

Check lug nuts/bolts torque.

•

Check after first 10 hours of operation, then at 50-hour intervals (see Figure 67 on page 11-2).

•

Check pick-up gauge wheels for correct pressure (see Figure 68 on page 11-2).

https://tractormanualz.com

Содержание 504 PRO


























































































































































Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды

Vermeer 504 PRO, Руководство оператора и по техническому обслуживанию

Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды