Vermeer 504 PRO Скачать руководство пользователя страница 14

Страница: 14 / 153

504PRO_604PRO_o-m2_00

504/604 PRO Baler

SAFETY MESSAGES

General Safety Messages

General safety messages appear in this Safety Messages section. Specific safety messages are located in appropriate sections of the manual where a
potential hazard may occur if the instructions or procedures are not followed.

A signal word "

DANGER

", "

WARNING

", or "

CAUTION

" is used with the safety alert symbol.

Safety signs with signal word "

DANGER

", "

WARNING

", or "

CAUTION

" are located near specific hazards.

DANGER

Indicates a hazardous situation that, if not avoided, will result in death or serious injury.

WARNING

Indicates a hazardous situation that, if not avoided, could result in death or serious injury.

CAUTION

Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.

NOTICE

Indicates information considered important, but not hazard-related.

2.1

Safety Symbol Explanation

This symbol is used in combination with an exclamation mark or
other symbols to alert you to the potential for death or serious
injury

Read Operator's and Maintenance Manual and safety signs
before operating machine.

Check machine before operating. Machine must be in good
operating condition and all safety equipment installed and
functioning properly.

https://tractormanualz.com

Содержание 504 PRO


























































































































































Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды

Vermeer 504 PRO, Руководство оператора и по техническому обслуживанию

Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды