Vermeer 504 PRO Скачать руководство пользователя страница 135

Страница: 135 / 153

504PRO_604PRO_o-m2_00

504/604 PRO Baler

Maintenance/Setting 11-19

11.8.4

Grind the Cutting Unit Knives

WARNING:

Chopper knives can cut fingers and hands.

WARNING:

Wear gloves and use suitable tool when

handling chopper knives.

WARNING:

Do not do work on the magnets of the blade holders if you have a cardiac pacemaker or other implant that

can be impaired by magnetic fields.

CAUTION:

Do not hit the knives with any kind of tool from the bottom. This may damage the magnets and splinters may

brake loose and cause injury.

CAUTION:

Wear protective gloves when you do work on the cutting unit blades.

NOTICE

Sharp blades save driving power, provide for a good cut quality and optimum crop throughput. How often the knives
must be regrinded depends on the type of crop and the amount of contamination.

Remove the Knives

1. Insert the cutting device to cutting position with the controller and double acting valve in the tractor.

2. Swivel the feed channel floor halfway down with the controller and double acting valve in the tractor.

Do not swivel completely down because the knives must still project from the feed channel floor.

3. Open the tail gate with the single acting valve in the tractor.

4. Make sure the PTO shaft is switched off, stop the tractor engine and remove the key.

5. Secure the tailgate with the hydraulic shutoff valve (1) (see Figure 4 on page 2-16) .

https://tractormanualz.com

Содержание 504 PRO


























































































































































Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды

Vermeer 504 PRO, Руководство оператора и по техническому обслуживанию

Результаты поиска

Содержание 504 PRO

Отзывы:

Бренды по названию

Популярные бренды