Ventev BTRM300 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 43

background image

BTRM Battery Test Remote Monitoring System – User Guide V3.2 |

ã

2021 Ventev | LIT SKU: 09834

17

9. Port Options Page

This allows the user to enable the IO channels and the system operation voltage.

Note that the BTRM400 has additional system voltages for 36V and 48V operation.

9.1

IO Channel 1

9.1.1

Analog Input 0-32V

This allows the user to enable an analog input level for triggering alarms from external
sources (door switches, solid state relays, etc.).

9.1.2

Digital Input Alarm if < 1V

This allows the user to enable a digital input logic levels that is less than 1 volt to trigger
an alarm from external sources (door switches, solid state relays, etc.).

9.1.3

Digital Input Alarm if > 2V

This allows the user to enable a digital input logic levels that is greater than 2 volt to
trigger an alarm from external sources (door switches, solid state relays, etc.).

9.1.4

Low Capacity Alarm

This allows the user to enable the channel relay to indicate a battery relate fault

•

Digital Out Normally Open: The relay closes when a fault is indicated.

•

Digital Out Normally Low: The relay opens when a fault is indicated.

«
...
15
16
17
18
19
...
»

Содержание BTRM300












































Отзывы:

Нет отзывов

Похожие инструкции для BTRM300

Бренд: Daewoo Страницы: 19

Бренд: Daewoo Страницы: 12

Бренд: Daewoo Страницы: 36

Бренд: Daewoo Страницы: 70

Бренд: iHealth Страницы: 14

Бренд: iHealth Страницы: 4

Бренд: IEM Страницы: 46

Бренд: Sanitas Страницы: 33

Бренд: Sanitas Страницы: 60

Бренд: Sanitas Страницы: 96

Бренд: Sanitas Страницы: 52

Бренд: Samsung Страницы: 48

Бренд: Samsung Страницы: 37

SyncMaster 460UTn-2

Бренд: Samsung Страницы: 26

Бренд: Samsung Страницы: 55

SyncMaster 206NW

Бренд: Samsung Страницы: 59

SYNCMASTER 152X/172X

Бренд: Samsung Страницы: 58

Бренд: Samsung Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды