Ventev BTRM300 Скачать руководство пользователя страница 13

Страница: 13 / 43

BTRM Battery Test Remote Monitoring System – User Guide V3.2 |

2021 Ventev | LIT SKU: 09834

7.1.4

Load Current

This is the measurement of the battery current.
Positive Load current 0.0 to 20.0 Amps BTRM300 / 0.0 to 10.0 Amps BTRM400

7.1.5

Supply Voltage

This is the measurement of power supply voltage.
Range 0.0 to 60.0V depending on selected range.

7.1.6

System Temperature

This is the BTRM temperature in °C.

7.1.7

Capacity

This is the measurement of the battery’s capacity level.
This capacity Good/Low status reading is present after the first test is completed.

7.1.8

IO Channel 1 – Analog V

This is the measurement of the voltage present at Channel 1 (ground referenced).
Range 0.0 to 60.0V (regardless of range selected)

7.1.9

IO Channel 1 – Digital In

This is the logic setting for IO Channel 1 (see port options menu) TRUE/FALSE

7.1.10

IO Channel 1 – Digital Out

This indicates that the IO Channel 1 relay has been set to indicate a battery relate fault
(see port options menu).
OFF The relay is set for normal operation.
ON

The relay is set to indicate a battery fault as diagnosed by the BTRM.

7.1.11

IO Channel 2 – Analog V

This is the measurement of the voltage present at Channel 2 (ground referenced).
Range 0.0 to 60.0V (regardless of range selected)

7.1.12

IO Channel 2 – Digital In

This is the logic setting for IO Channel 2 (see port options menu) TRUE/FALSE

7.1.13

IO Channel 3 – Analog In

This is the measurement of the voltage present at Channel 3 (ground referenced)
Range 0.0 to 60.0V (regardless of range selected)

7.1.14

IO Channel 4 – Analog In

This is the measurement of the voltage present at Channel 4 (ground referenced)
Range 0.0 to 60.0V (regardless of range selected)

7.1.15

System Voltage Type

The type of batter voltage the system is operating at.
Not available on all modes – check the Port Options menu to confirm System Voltage
Type

7.1.16

System Up Time

The time the system has been operational.

Содержание BTRM300












































Результаты поиска

Содержание BTRM300

Отзывы:

Похожие инструкции для BTRM300

Бренды по названию

Популярные бренды

Ventev BTRM300, Руководство пользователя

Результаты поиска

Содержание BTRM300

Отзывы:

Похожие инструкции для BTRM300

Бренды по названию

Популярные бренды