Vendlet 6000000 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 56

background image

24

PART 2 - User manual

ATTACHING THE SHEETS

Place a slide sheet directly on top of the mattress, followed by the turning sheet
which is then attached to the two bars. Slide sheets and turning sheets are available
in standard bed sizes and with increased width which makes the VENDLET V5 and
VENDLET V5+ systems suitable for wider beds as well.

Turning sheet width

Slide sheet width

Fits mattress widths

350 cm (standard)

95 cm (standard)

80-90 cm (standard)

400 cm

115 cm

95-110 cm

450 cm

135 cm

115-130 cm

You can also purchase disposable turnings sheets and slide sheets. The disposable
sheets are only avalible in one size.

Slide sheet

1. Fold the slide sheet corner elastic straps

around the mattress.

2. Check that the surface is smooth and even

without creases and folds. Make sure that
slippery side is facing upwards.

3. Fasten the velcro tapes around the

mattress frame. It is important
that the tapes are fastened
around the frame under the
mattress and not around the bed frame
as this will prevent the back, thigh, and
foot parts of the bed from being raised.
The tapes are long enough for thick mat-
tresses.

The slide sheet is subject to extensive wear

and must be checked regularly. The friction of the turning sheet against the mattress
will increase and the comfort of the patient will be reduced during moving and other
forms of handling if the bed is not fitted with a slide sheet or the slide sheet has been
damaged.

When an alternating air mattress is fitted with a slide sheet, it is important that the
velcro tapes are not fastened around the frame under the mattress too tightly as this
could disrupt the function of the alternating air mattress. Consequently, the mattress
should be fully inflated during fitting.

«
...
22
23
24
25
26
...
»

Содержание 6000000

























































Отзывы:

Нет отзывов

Похожие инструкции для 6000000

Бренд: OMCA Страницы: 72

Бренд: Camozzi Страницы: 2

Бренд: Oktober Страницы: 22

Бренд: NARGESA Страницы: 50

Бренд: Panasonic Страницы: 180

Бренд: HAMAR LASER Страницы: 49

Бренд: Olsen Страницы: 56

Бренд: Waterous Страницы: 5

Бренд: 3TECH Страницы: 32

Бренд: 4EVAC Страницы: 15

Бренд: Bacharach Страницы: 48

Бренд: JB-Lighting Страницы: 40

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Velleman Страницы: 16

Бренд: Velleman Страницы: 11

Бренд: Wasp Страницы: 50

QUICK-ALIGN Vari-Flex

Бренд: Össur Страницы: 36

Бренд: Össur Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды