Vendlet 6000000 Скачать руководство пользователя страница 50

Страница: 50 / 56

PART 3 - Technical manual

Replacing the motor in a bar

1. Raise the bar and remove the turning

sheet from the bar on which the motor is
to be replaced.

2. Disconnect the power cable from the

mains outlet.

3. Disconnect the motor bar cable from the

control unit and remove the bar from the
two actuator fittings.

4. Remove the Allen screw at the motor end

of the bar and pull the motor out.

5. Unscrew the small pivot screw on the

motor fitting and remove it.

6. Mount the motor fitting on the new motor

and attach it using the pivot screw.

7. Place the motor inside the bar and attach

it using the Allen screw you removed
earlier.

8. Mount the bar on the two actuator fittings

and connect the cable to the control unit.

9. Reconnect the power cable to the mains

outlet.

10. Reset the system by simultaneously

pressing the two top buttons on the hand
control. You will hear a series of rhythmic
beeps. Press and hold the buttons until
the beeping stops.

11. Check whether the bar is working

properly.

Remove the Allen screw

Remove the motor from the bar

Unscrew the small pivot screw and remove

the motor fitting

Mount the motor fitting on the new motor

Содержание 6000000

























































Результаты поиска

Содержание 6000000

Отзывы:

Похожие инструкции для 6000000

Бренды по названию

Популярные бренды

Vendlet 6000000, Руководство пользователя

Результаты поиска

Содержание 6000000

Отзывы:

Похожие инструкции для 6000000

Бренды по названию

Популярные бренды