background image

     

Page

 

32

Wireless Pressurized Line Leak Detection Tests 

(WPLLD Option)

TO START A WPLLD TEST

In the Operating mode, press 

Function

 until the display reads:

Press 

Step

 and the display reads:

Press 

Step

 to accept all lines. To select a single line, press 

Change

 

until 

you see the line you want, then press 

Enter

 

and 

Step

. The display reads:

This step lets you select a 3.0, 0.2, or 0.1 gph (0.38, 0.76, 11.3 lph) line 
leak test to run on the selected line(s). If your console does not have 0.2 or 
0.1 gph test options, you will not see these selections.

START LINE PRESSURE TEST
PRESS <STEP> TO CONTINUE

SELECT LINE
ALL LINES

SELECT TEST TYPE
3.0 GPH

To select a 3.0 gph test, press 

Step

,

 or press 

Change

 to select a 

0.2 or 0.1 gph test, then press 

Enter

To select a 3.0 gph test, press 

Step

. The display reads:

To run the selected test, press 

Step

. The system displays the mes-

sage (in this example for all lines):

Press 

Enter

 to begin the test. The display reads:

To exit this function, press 

Step

.

3.0 GPH
PRESS <STEP> TO CONTINUE

START LINE TEST: ALL LINE
PRESS <ENTER> 

W#: TEST PENDING
PRESS <STEP> TO CONTINUE

NOTE: WPLLD is available with UL approved consoles only.

Содержание TLS-3 Series










































Отзывы: