55
User Manual
[MENU] + [MENU] + "INPUT/OUTPUT" + [ENTER] + "PORT 1 INPUT"
+ [ENTER] + "C-COM" + [ENTER]
The modem C-COM can be connected also to the Port 2 (except for
MAP 7cwi
Plus GPS)
, Port 3 (except for
MAP 7wi Plus GPS/MAP 7cwi Plus GPS)
and
Port 4/5 (except for
MAP 11csE Plus GPS/MAP CX Plus)
, in this case select the
format on the used port.
NOTE
The connection is valid for the C-COM IR and C-COM RS232 too.
NMEA Output
The chart plotter allows customizing the NMEA-0183 sentence transmitted on
each port. Each port can transmit a different set of sentences among: GLL, VTG,
BOD, XTE, BWC, RMA, RMB, RMC, APB, WCV, GGA, HSC, HDG:
[MENU] + [MENU] + "INPUT/OUTPUT" + [ENTER] + "PORT n OUTPUT SEN-
TENCES" + [ENTER].
Where:
n = 1/2/3 for
MAP 11csE Plus GPS
n = 1/4/5 for
MAP 7cwi Plus GPS
n = 1/2/4/5 for
MAP 7wi Plus GPS
n = 1/2/3/4/5 for
MAP 7w Plus GPS/MAP CX Plus
Send/Receive Routes & Marks
E
Sets the desired port used for transferring User Points and Routes functions:
[MENU] + [MENU] + "INPUT/OUTPUT" + [ENTER] + "SEND/REC ROUTES &
MARKS" + [ENTER] + "Port n" + [ENTER]
Where:
n = 1/2/3 for
MAP 11csE Plus GPS
n = 1/4/5 for
MAP 7cwi Plus GPS
n = 1/2/4/5 for
MAP 7wi Plus GPS
n = 1/2/3/4/5 for
MAP 7w Plus GPS/MAP CX Plus
C-Link
E
Sets the Primary or Secondary Station (see dedicated Chapter):
[MENU] + [MENU] + "INPUT/OUTPUT" + [ENTER] + "C-LINK" +
[ENTER] + "Secondary Station/Primary station" + [ENTER]
External NMEA
E
Sets the displaying or not of the following items (max four items) in the Logic
Data Display Page: Speed, Heading (HDG), Depth, Drift, Set, Wind Speed True,
Wind Direction True, Wind Speed App, Wind Direction App, Speed Over Ground
(SOG), Course Over Ground (COG), Distance, Bearing (BRG), Time To Go (TTG),
Cross Track Error (XTE), Velocity Made Good. When any item is receiving or calcu-
lated a small black square appears before On/Off indication.
[MENU] + [MENU] + "INPUT/OUTPUT" + [ENTER] + "EXTERNAL NMEA" +
[ENTER]
External Signal
Sets the External Output:
[MENU] + [MENU] + "INPUT/OUTPUT" + [ENTER] + "EXTERNAL SIGNAL"
+ [ENTER]
Then choose your preferred setting among External Alarm (when activated, this
pin goes to GND level. It is used to command an external buzzer), External Power
(it is command switch for the Radar. It must be used in conjunction with the Radar
Junction box device) and Off.
Содержание MAP 11csE Plus GPS
