Varta Pulse neo 3 Скачать руководство пользователя страница 48

Страница: 48 / 148

Installation

Transport regulations

WARNING

Incorrect transport due to insufficient
expertise.

Potential risk of death and property damage.

The energy storage system and its
components may only be transported by the
manufacturer and qualified and certified
electricians.

Be careful during transport.

Always observe all transport regulations.

Energy storage system and battery module

Must not be stored inside the transport vehicle.

The energy storage system must not be
transported if a battery module has already been
installed.

The packaging of battery modules must not be
opened by the driver or assistant driver.

Energy storage system and battery module

A certified ABC fire extinguisher with a minimum
capacity of 2 kg must be available at the transport
vehicle.

Observe the symbols on the packaging.

The parts may only be transported in closed
vehicles.

The load must be properly secured.

The battery module may only be transported in its
dedicated transport packaging.

Observe all requirements according to applicable
regulations for transport of hazardous goods
(GGVSEB) and ADR regulations.

Содержание Pulse neo 3





















































































































































Результаты поиска

Содержание Pulse neo 3

Отзывы:

Бренды по названию

Популярные бренды

Varta Pulse neo 3, Руководство по эксплуатации

Результаты поиска

Содержание Pulse neo 3

Отзывы:

Бренды по названию

Популярные бренды