ISTRUZIONI PER L’USO
4
87-900-855-01 (B)
MESSAGGIO
DESCRIZIONE
AZIONE CORRETTIVA
CHECK CONNECTION TO
PUMP
Malfunzionamento nel collegamento tra
pompa e controller (P31).
Verificare che il cavo di collegamento tra
pompa e controller sia ben fissato da
entrambe le estremità e non sia interrotto.
Premere due volte il pulsante START per
riavviare la pompa.
PUMP WAITlNG INTERLOCK
È attivo il segnale di interlock presente
sul connettore P1 a causa
dell'interruzione del corto circuito tra il
pin 3 ed il pin 8 del connettore J1, o a
causa dell'apertura del segnale di
interlock esterno.
Ripristinare il corto circuito tra il pin 3 ed il
pin 8 del connettore J1, o chiudere il segnale
di interlock esterno
FAULT: OVERTIME
La pompa non ha raggiunto la velocità
prevista di 5500 KRPM 12 minuti dopo
l’avvio con SOFT START deselezio-
nato.
Verificare che il sistema non presenti delle
perdite. Premere due volte il pulsante
START per riavviare la pompa.
FAULT: PUMP
OVERHEATED
La temperatura ha superato uno dei
seguenti valori di soglia:
- 65 °C per i cuscinetti
- 90 °C per il motore
- 60 °C per l’acqua.
Attendere che la temperatura ritorni al di
sotto della soglia.
Premere due volte il pulsante START per
riavviare la pompa.
FAULT: CONTROLLER
OVERHEATED
La temperatura del trasformatore del
controller ha superato i 90 °C oppure la
temperatura sul radiatore dei Mosfets di
uscita è superiore a 60
°
C.
Attendere che la temperatura ritorni al di
sotto della soglia. Premere due volte il
pulsante START per riavviare la pompa.
FAULT: OVERLOAD
Durante il funzionamento normale
(dopo la fase di avvio) la corrente
assorbita dalla pompa è maggiore di
quella programmata (25 A).
Verificare che il rotore della pompa abbia la
possibilità di ruotare liberamente. Premere
due volte il pulsante START per riavviare la
pompa.
FAULT: SHORT CIRCUIT
Durante il funzionamento normale la
connessione di uscita è in corto circuito
(corrente di uscita maggiore di 60 A).
Verificare i collegamenti tra pompa e
controller. Premere due volte il pulsante
START per riavviare la pompa.
Verificare l’isolamento tra il motore e la
pompa.
SYSTEM OVERRIDE
La pompa è stata fermata da un
segnale di emergenza proveniente da
un contatto remoto.
Staccare il cavo di alimentazione del
controller e correggere la causa
dell'emergenza.
Ricollegare il cavo di alimentazione e
premere due volte il pulsante START per
riavviare la pompa.
OVERVOLTAGE
Si è verificato un guasto nella sezione
di alimentazione del controller, o il
controller ha ricevuto un segnale
spurio.
Premere due volte il pulsante START per
riavviare la pompa.
Se il messaggio si ripresenta rivolgersi alla
Varian per la manutenzione.
OIL LEVEL AT MIN
Il sensore del livello olio ha rilevato un
livello inferiore a quello di sicurezza.
Provvedere alla manutenzione della pompa
secondo le modalità descritte nell’apposito
manuale.
Содержание Turbo-V 6000
Страница 2: ...Turbo V 6000 Controller...
Страница 3: ......
Страница 4: ......
Страница 80: ...TECHNICAL INFORMATION 74 87 900 855 01 B...