MODE D'EMPLOI
12
87-900-855-01 (B)
MESSAGE
DESCRIPTION
INTERVENTION
CHECK CONNECTION
TO PUMP
Dysfonctionnement de la connexion
entre la pompe (P31).
S'assurer que le câble de connexion en-
tre la pompe et le contrôleur et le con-
trôleur est bien fixé aux deux extrémités
et qu'il n'est pas coupé. Presser deux fois
l'interrupteur START pour réactiver la
pompe.
PUMP WAITING INTERLOCK
Le signal d'interlock situé sur le con-
necteur P1 est actif à cause de la
coupure du court-circuit entre le pin 3 et
le pin 8 du connecteur J1 ou à cause de
l'ouverture du signal d'interlock exté-
rieur.
Rétablir le court-circuit entre le pin 3 et le
pin 8 du connecteur J1 ou fermer le si-
gnal d'interlock extérieur.
FAULT: OVERTIME
12 minutes après le démarrage avec
fonction SOFT START invalidée, la
pompe n’a pas atteint la vitesse prévue
de 5500 K tr/min.
Contrôler que le système ne présente
aucune fuite. Appuyer deux fois sur la
touche START pour relancer la pompe.
FAULT: PUMP
OVERHEATED
La température est supérieure à l’une
des valeurs de seuil suivantes:
- 65°C pour les paliers
- 90 °C pour le moteur
- 60°C pour l’eau
Attendre que la température retourne au-
dessous du seuil.
Presser deux fois l'interrupteur START
pour remettre la pompe en marche.
FAULT: PUMP
OVERHEATED
La température du transformateur du
contrôleur est supérieure a 90°C ou la
température sur le radiateur des Mo-
sfets de sortie est supérieure à 60°C.
Attendre que la température retourne au-
dessous du seuil.
Presser deux fois l'interrupteur START
pour remettre la pompe en marche.
FAULT: OVERLOAD
Pendant le fonctionnement normal
(après la phase de mise en marche), le
courant absorbé par la pompe est plus
grand que celui qui a été programmé
(25 A).
S'assurer que le rotor de la pompe a la
possibilité de tourner librement.
Presser deux fois l'interrupteur START
pour remettre la pompe en marche.
FAULT: SHORT CIRCUIT
Pendant le fonctionnement normal la
connexion de sortie est en court-circuit
(courant de sortie plus grand que 60 A).
Vérifier les connexions entre la pompe et
le contrôleur.
Presser deux fois l'interrupteur START
pour remettre la pompe en marche.
Contrôler l’isolation entre le moteur et la
pompe.
SYSTEM OVERRIDE
La pompe a été arrêtée par un signal
d'alerte provenant d'un contact éloigné.
Débrancher le câble d'alimentation du
contrôleur et corriger la cause de
l'alerte.
Reconnecter le câble d'alimentation et
presser deux fois l'interrupteur START
pour remettre la pompe en marche.
OVERVOLTAGE
Il s'est produit une panne de la section
d'alimentation du contrôleur, ou bien le
contrôleur a reçu un faux signal.
Presser deux fois l'interrupteur START
pour remettre la pompe en marche.
Si le message se présente à nouveau,
s'adresser à Varian pour l'entretien.
OIL LEVEL AT MIN
Le jauge d’huile indique un niveau
inférieur au niveau de sécurité.
Effectuer l’entretien de la pompe en sui-
vant les indications fournies dans le ma-
nuel d’entretien.
Содержание Turbo-V 6000
Страница 2: ...Turbo V 6000 Controller...
Страница 3: ......
Страница 4: ......
Страница 80: ...TECHNICAL INFORMATION 74 87 900 855 01 B...