Van Der Stahl V-460G Series, Руководство по эксплуатации

Страница: 56 / 116

V-460G/610G Series Operating Instructions Ver.4.02E
56
（ The mark “ 〜 ” under the cursor indicates it is blinking. ）
［ 0 x ］▼▲CHG Move N x
HT xx
O
C x . x s CT xx
O
C
〜
［ 0 x ］▼▲CHG Move N x
1VG‒ xxx kPa G xx . x sec
GCT xx . x sec G xx . x sec
HT xx
O
C x . x s CT xx
O
C
（
The mark “
〜
” under the cursor indicates it is blinking.
）
〜
［ 0 x ］▼▲CHG Move N x
1VG‒ xxx kPa G xx . x sec
GCT xx . x sec G xx . x sec
HT xx
O
F x . x s CT xx
O
F
（ The mark “ 〜 ” under the cursor indicates it is blinking. ）
〜
［ 0 x ］▼▲CHG Move N x
1VG‒ xxx kPa G xx . x sec
GCT xx . x sec G xx . x sec
HT xx
O
C x . x s CT xx
O
C
（
The mark “
〜
” under the cursor indicates it is blinking.
）
〜
［ 0 x ］▼▲CHG Move N x
1VG‒ xxx kPa G xx . x sec
GCT xx . x sec G xx . x sec
HT xx
O
F x . x s CT xx
O
F
（ The mark “ 〜 ” under the cursor indicates it is blinking. ）
2
Using the [ ] [ ] keys, set the desired nozzle
stroke. Setting range is from 1 to 8 referring to
the below table.
3
Press the [ ] key to return the display.
NZ stroke# Nozzle moving distance
1 10mm
2 20mm
3 30mm
4 40mm
5 50mm
6 60mm
7 70mm
8 80mm
※ Nozzle stroke accuracy is ±2 to 3mm.
※ Nozzle stroke is the distance from the sponge
rubber surface to the tip of nozzle.
3
Set the circulating gas-flushing time. Move
the cursor to the first digit of circulating-gas
timer “G xx.x sec” using the [ ] key.
Adjust the circulating gas time by pressing:
a) the [ ] key to increase the value.
b) the [ ] key to decrease the value.
[Setting range: 0.1 ~ 99.9 seconds]
The value will increase or decrease in 0.1
seconds increment by pressing the key once. If
you hold the key in, the numeric value will
increase or decrease continuously.
4
Set the second gas-flushing time. Move the
cursor to the first digit of second gas timer
“G xx.x sec” using the [ ] key.
Adjust the second gas time by pressing:
a) the [ ] key to increase the value.
b) the [ ] key to decrease the value.
[Setting range: 0.0 ~ 99.9 seconds]
The value will increase or decrease in 0.1
seconds increment by pressing the key once. If
you hold the key in, the numeric value will
increase or decrease continuously.
1
Ŷ How to change the nozzle stroke of the
currently displayed operation pattern:
>> Press the [ ] key. The below display will
be shown on the screen. Go to procedure
2
.
Ŷ How to change the nozzle stroke of the
operation pattern NOT currently displayed:
>> Refer to “8-4-2 Select the desired operation
QXPEHU´ĺSDJH.
After selecting the desired number, press the
[ ] key and go to procedure
2
.
8-4-16 Setting nozzle stroke
Nozzle stroke (mm)
Sponge rubber