Valtra Versu N Series Скачать руководство пользователя | Manualshive

Страница: 332 / 518

background image

•

Wash the tractor using a pressure washer.
Keep the nozzle of the pressure washer at least 30 cm from the sealing

points and paint work. The temperature of the washing water must not be

higher than 50°C.
NOTE:
Do not use special nozzles, such as turbo nozzles, when washing. Follow the

instructions of the pressure washer manufacturer.

•

Do not let the water get into the cab air filter when washing the cab sides.
The cab air filter is in the side plate of the roof, usually on the left.

•

Do not wash the inside of the cab with a pressure washer or running water.

•

Do not point the pressure washer towards electrical equipment, electrical

connectors, lead-through points, bearings, seals and locks.
Use lower pressure (6,5 MPa / 65 bar) and point the water diagonally to the

above points. Do not point the pressure washer towards the radar sensor

(minimum distance 1 m and maximum pressure 6,5 MPa / 65 bar).

•

When using a cold grease remover, do not keep the tractor in sunshine.
The paint work may get damaged, if the painted surface is hot.

•

Wax the painted surfaces.

After washing, grease the lubricating points and the joints and lubricate the

bearings with oil.

4.3.1.1

Cleaning the engine compartment

Keep the engine surface clean to avoid the risk of fire.
NOTE:
Protect the environment by following the environmental regulations. The washing

place must have a separator outlet when using detergents.

•

Let the engine cool down for a few minutes before washing.
IMPORTANT: To avoid the risk of fire, do not wash the engine when it is hot.

•

Wash the engine carefully using pressure washer.
Keep the nozzle of the pressure washer at least 30 cm from the sealing

points and paint work. The temperature of the washing water must not be

higher than 50°C.
•

Use lower pressure, 6.5 MPa / 65 bar.

•

Point the water jet diagonally to the engine.

NOTE:
Do not use special nozzles, such as turbo nozzles, when washing. Follow the

instructions of the pressure washer manufacturer.

4. Maintenance

- 330 -

«
...
330
331
332
333
334
...
»

Содержание Versu N Series







































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Versu N Series

PROXIMA PLUS 2011 Series

Бренд: Zetor Страницы: 204

Бренд: Washtech Страницы: 30

Бренд: MTD Страницы: 33

Бренд: Belarus Страницы: 358

FENDT 800 Vario SCR Series

Бренд: AGCO Страницы: 51

Бренд: Komatsu Страницы: 4

Бренд: Saton Страницы: 219

Independence HI-I-LR-48

Бренд: Homestead Страницы: 15

Бренд: Bolens Страницы: 13

Бренд: Bolens Страницы: 16

Бренд: Bolens Страницы: 16

Бренд: Bolens Страницы: 20

Бренд: Bolens Страницы: 24

Бренд: Bolens Страницы: 32

Бренд: Bolens Страницы: 107

Бренд: New Holland Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды