Valor L1 Series Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 72

Valor L1 Series Скачать руководство пользователя страница 58

58

QUALIFIED
INSTALLER

Close

Open

Injector elbow bracket,

burner side

Injector elbow

Air shutter

Setting air shutter

Battery holder
connection

Reset

button

Accessing air shutter

Check Operation

Turn the ﬁ replace ﬂ ame up and down using the
remote control to conﬁ rm that the full range of inputs
is achieved—see the remote control operation
instructions on pages 8–13.

Adjust Aeration

(if necessary)

Light the ﬁ re and allow the unit to warm up for 10–15
minutes to evaluate the ﬂ ame picture. The burner is
equipped with an adjustable shutter to control primary
aeration (natural gas only). The shutter is factory-set to
an aeration gap which will give optimum performance
for the vast majority of installations.

Depending of the fuel bed used, altitude and other
considerations, the ﬂ ame picture may be improved by
adjusting the aeration. The need for adjustment should
be determined only by operating the appliance with the
fuel bed, panels and window installed and evaluating
the ﬂ ame picture after a 15-minute warm-up.

Increasing aeration

will cause the ﬂ ames to appear

more transparent and blue showing more ceramic
eﬀ ects glow.

Decreasing aeration

will cause the ﬂ ames to appear

more yellow or orange showing less ceramic eﬀ ects glow.

Too little aeration may result in black carbon
forming and dropping into the fi rebox.

To access the air shutter, remove the front middle
platform as indicated. The air shutter is located under
the burner as shown in the illustrations.

Air Shutter

Installation

Set-up Remote Control

The receiver and the handset of the remote control sys-
tem must be initially synchronized before the ﬁ rst use.

1. Insert one 9 V alkaline battery in the handset.
2. Locate the Reset button on the top side of the

receiver.

3. With a sharp object, press and hold the receiver’s reset

button until you hear one short and one long beeps.
Release the reset button after the second beep.

4. Within the subsequent 20 seconds, press the (small

ﬂ ame button ( ) on the remote handset until you
hear two short beeps conﬁ rming the synchronization
is set.
This is a one time setting only and is not required
when changing the batteries in the remote receiver.
The remote control system is now ready to use.

«
...
56
57
58
59
60
...
»

Содержание L1 Series









































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды