Valor L1 Series Скачать руководство пользователя страница 54

Страница: 54 / 72

QUALIFIED
INSTALLER

Installation

WARNING

CHOKING HAZARD!

Ensure that the ﬁ replace

area is clear of embers/splinters particles as these
could be ingested by small children. Vacuum area
after installation.

IMPORTANT:

Homologated for use only with the ce-

ramic embers and splinters provided with your Valor
ﬁ replace. The use of any other products may void
your ﬁ replace warranty.

2. Carefully spread the embers in a single layer on the

surface of burner between the logs.

Do not pile up

the embers to avoid blocking the burner ports

3. Some embers may be added on the platform to

cover the edge of the burner and the round holes.

4. Spread some splinters to the embers.

Pilot shield

NOTE:

Ensure the area

within

the pilot shield is

clear of embers or splinters.

1500SWK—Split Wood Kit installed

Pilot shield

Содержание L1 Series









































































Результаты поиска

Содержание L1 Series

Отзывы:

Бренды по названию

Популярные бренды

Valor L1 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание L1 Series

Отзывы:

Бренды по названию

Популярные бренды