Valor L1 Series Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 72

Valor L1 Series Скачать руководство пользователя страница 36

36

QUALIFIED
INSTALLER

Only qualiﬁ ed licensed or trained personnel
should install this appliance.

Installer—READ THIS FIRST

1. YOU NEED TO KNOW FROM THE

HOMEOWNER:
- Will the optional LDK Duct Kit be used;
- The height of the unit and hearth if used;
- The thickness and type of the wall ﬁ nish
around the ﬁ rebox opening;
- What accessories (trim, decorative lighting,
etc.) will be installed with this ﬁ replace;
- The venting conﬁ guration.

2. Unpack the appliance, removing all items packed

inside and around the appliance.

3. Check that you have everything, using the Pack

Content sheet. Also, check that you have:

◊ a fuel bed (packed separately)
◊ a set of liners (packed separately)
◊ LDK HeatShift kit if used.

4. Carefully read the Installer’s Checklist included with

the ﬁ replace for the installation sequence.

Installation Planning

1/2” (13mm) thick
non-combustible
cement board

Gypsum board
up to perimeter
of cement board

Min.

9-1/4”

(235 mm)

Min.

44-1/2”

(1130 mm)

Min.

20-1/2”

(521 mm)

14-3/4”

(375 mm)

Board flush with
bottom of heater;
add extra if
overlapping
framing.

40”

(1016 mm)

Min. 48”

(1219 mm)

1/4”

(235 mm)

Possible scr

ew loc

(in the designat

ed

ar

d flush with bo

of heat

er; add ex

tra

overlapping fr

aming

Wider trim (1550)
can adjust up to 1”
forward of surface
of cement board

Narrow trim (1575)
can adjust up to
5/8” forward of
surface of cement
board

Plan Wall Finish

Non-Combustible Materials Speciﬁ cations

Material which will not ignite and burn. Such materials
are those consisting entirely of steel, iron, brick, tile,
concrete, slate, glass or plasters, or any combination
thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750 °C shall be considered
non-combustible materials.

Combustible Materials Speciﬁ cations

Materials made of or surfaced with wood, compressed
paper, plant ﬁ bers, plastics, or other material that
can ignite and burn, whether ﬂ ame proofed or not,
or plastered or unplastered shall be considered
combustible materials.

Non-combustible cement board

The L1 Linear ﬁ replace requires a 1/2” (13 mm) thick
non-combustible cement board to be used as a wall
surface immediately surrounding the unit on each
side—see diagram for minimum coverage.

Minimum cement
board dimensions

«
...
34
35
36
37
38
...
»

Содержание L1 Series









































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды