manualshive.com logo in svg

Valor L1 Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Valor L1 Series Скачать руководство пользователя страница 20

20

QUALIFIED 
INSTALLER

X

Model 

JN

JP

Gas

Natural Propane

Altitude (Ft.)*

0-4,500 feet*

Input Maximum (Btu/h)

30,000

28,000

Input Minimum (Btu/h)

18,000

18,500

Manifold Pressure (in w.c.)

4.0”

9.5”

Minimum Supply Pressure 
(in w.c.)

5”

11”

Maximum Supply Pressure 
(in w.c.)

10”

14”

Main Burner Injector Marking

850

300

Pilot Injector Marking

51

30

Min. Rate By-Pass Screw

220

160

 Specifi cations

Approval & Codes

This appliance is certifi ed to ANSI Z21.88-2016/CSA 
2.33-2016 American National Standard / CSA Standard 
for 

Vented Gas Fireplace Heaters

 for use in Canada 

and USA, and to CGA 2.17-91 

High Altitude Standard in 

Canada

. This appliance is for direct vent installations.

This appliance complies with CSA P.4.1-15 

Testing 

method for measuring annual 

fi

 replace e

ffi

  ciencies

.

The installation must conform to local codes or, in the 
absence of local codes, with the 

National Fuel Gas Code, 

ANSI Z223.1/NFPA 54

 or the 

Natural Gas and Propane 

Installation Code CAN/CGA-B149.1

. Only qualifi ed 

licensed or trained personnel should install this appliance.
This appliance must be electrically grounded in 
accordance with local codes, or, in the absence of local 
codes, with the 

National Electrical Code, ANSI/NFPA 

70

 or the 

Canadian Electrical Code, CSA C22.1

.

Ratings

*High Altitude Installations

I

nput ratings are shown in BTU per hour and are 

certifi ed without deration for elevations up to 4,500 feet 
(1,370 m) above sea level.
For elevations above 4,500 feet (1,370 m) in USA, 
installations must be in accordance with the current 
ANSI Z223.1 and/or local codes having jurisdiction. 
Heating value of gas in some areas is reduced to 
compensate for elevation—consult your local gas utility 
to confi rm.
For installations at elevations above 4,500 feet 
(1,370 m) in Canada, please consult provincial and/or 
local authorities having jurisdiction.

   

Supply Gas

Heater engine 1500JN is used with natural gas.
Heater engine 1500JP is used with propane gas.

The supply pressure must be 
between the limits shown in 
the Ratings section above.
The supply connection is 3/8” 
NPT male and located on the 
left hand side of the fi rebox. 
A shut-off  valve (not supplied) 
is required on the supply line to isolate the unit during 
service. See 

Gas Supply Installation

 section for details.

Conversion Kits

The 1500 L1 is supplied as natural gas or propane gas 
and is fi eld convertible between fuels. See instructions 
packaged with the conversion kit for further information.

  Electrical Wiring

The 1500 is designed to run on battery power and 
does not require an electrical power source to operate 
as a heater. However, it requires electrical power to 
operate optional 1565LLK Linear Lighting Kit,   1595CFK 
Circulating Fan Kit or 1270RBK Remote Blower Kit.

 LDK HeatShift Duct Kit

The 1500J is designed to allow the installation of the 
optional LDK HeatShift Duct Kit, a convection system 
that  redistributes the warm air fl ow away from the 
fi replace opening to a more desirable location using 
natural convection, without use of a fan. 
The warm air fl ow may be relocated to a position higher 
up the wall, out the sidewalls, or even to another room. 
The result is much cooler wall temperatures above the 
fi replace opening for locating televisions, artwork, etc.

Please note that the framing and mantel clearances 
are aff ected by the installation of the LDK.

 Refer 

to the installation manual packed with the kit for more 
information.

This appliance is designed and approved as a 
supplemental heater and provides the potential 
for most energy conservation when used while 
attended. The use of an alternate primary heat 
source is advisable.

Outdoor Conversion Kit

The 1500J models are supplied standard for indoor 
applications and may be adapted for installation in 
specifi c “outdoor” applications protected from weather 
as defi ned in the GV60CKO outdoor conversion kit 
manual.

WARNING

O p t i o n a l   e l e c t r i c a l   a c c e s s o r i e s 
A R E   N O T  A L L O W E D   w h e n   a d a p t i n g 
a p p l i a n c e   f o r   o u t d o o r   u s e .

!

Содержание L1 Series









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды