Valor L1 Series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 72

Valor L1 Series Скачать руководство пользователя страница 38

38

QUALIFIED
INSTALLER

Fold ﬂ at
standoﬀ s

Standoﬀ s installed

Standoﬀ

Remove top outlet (6 screws)

Remove heat shield (3 screws)

Fit Standoﬀ s

The standoﬀ s are supplied ﬂ at on
the ﬁ rebox sides and ﬁ xed at one
end. Swivel up the ﬂ at standoﬀ s,
bend them as shown and ﬁ x the
loose end to the top of the ﬁ rebox.

Remove Heat Shield

Remove the heat shield from the top of the appliance
case (3 screws). If using a rear outlet, keep the shield
to reinstall after converting the top to rear outlet—see
next subsection. If using the top outlet or the LDK
HeatShift Duct Kit, discard the shield.

Swivel the outlet so
that it is oriented
towards the rear and
reinstall to heater
(6 screws)

Reinstall heat
shield to top of
appliance
(3 screws)

Rear outlet with required heat shield

Convert from Top to Rear Outlet

(if required)

This unit is supplied with a top vent outlet which can
be ﬁ eld-converted to a rear vent outlet.

Please note that the rear outlet requires the instal-
lation of the heat shield on top of the heater case
as indicated.

1. Remove the top outlet collar (6 screws).

2. Swivel the collar and install as a rear outlet (6 screws).

3. Reinstall the heat shield to the top of the appliance

case (3 screws).

Fit optional LDK HeatShift Duct Kit’s
take-oﬀ collars to appliance

(if used)

See installation instructions packed with the LDK kits
for details.

Installation

«
...
36
37
38
39
40
...
»

Содержание L1 Series









































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды