Valor L1 Series Скачать руководство пользователя страница 39

Страница: 39 / 72

QUALIFIED
INSTALLER

Section Views

Window frame

Bottom railing

NON-

COMBUSTIBLE M

ATERIALS ONL

READ INSTRUC

TIONS

MATÉRIA

UX INC

OMBUSTIBLES SEULEMENT

CONSUL

TEZ LE GUIDE D

’INST

ALLA

TION

ﬂ ush

front

face of

appliance

mounting

tabs (4)

Appliance ﬂ ush to framing

Remove Window

The window is held in place by a spring-loaded lever on
each side.
1. To remove the window, locate the levers on each

side of the window towards the top. Using your
ﬁ nger, pull the lever towards you and unhook it from
the window frame bracket.

2. Gently pull the top of the window outward.
3. Lift the window out of its bottom railing and set it

aside in a safe place to avoid damage.

Installation

Fit Appliance into Framing

1. Remove the 4 screws

retaining the engine

its pallet.

2. Taking great care not

to cut your hands on
the sheet metal edges,
lift the appliance out
of its packing base
and place it in the
framing.

Make sure that

the unit is at the right height with consideration to
the height of the hearth or combustible

ooring.

3. Fold out four mounting tabs and recess the

appliance in the framing as shown.

4. Fasten the unit to framing using 4 screws or nails at

the mounting tabs.

Note:

The sheet metal front face of the appliance is

ﬂ ush with the framing studs.

Complete Installation of optional LDK
HeatShift Duct Kit

(if used)

See installation instructions packed with the LDK kits
for details.

Содержание L1 Series









































































Результаты поиска

Содержание L1 Series

Отзывы:

Бренды по названию

Популярные бренды

Valor L1 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание L1 Series

Отзывы:

Бренды по названию

Популярные бренды