VALCO MELTON MCP-8I Скачать руководство пользователя страница 40

Страница: 40 / 63

www.valcomelton.com | TEL: (1) 513-874-6550 | FAX: (1) 513-874-3612

Doc. IS0xxx

Rev.04 | Date: August 25, 2021

MCP-8I Quick Start Guide

How to Learn an Unglued Sample (Learn the Reference)

Only necessary for the

WHITE CGS-40S

Sensor running in

Manual Reference Mode

1. Navigate to the

‘Inspection Window’

by pressing the button labeled ‘

INSPECT

’.

Figure 79: Navigating to the Inspection Window

2. To Start the Learn Process for an Unglued Sample, Press the button labeled ‘

REF

’.

Figure 80: Learn Unglued Sample Button

3. When the ‘

Waiting…

’ prompt appears, feed product into the machine. Once the Learn is

completed, Confirm the ‘

Learn was successful

’ prompt.

Figure 81: Unglued Sample Learn Prompts

Note1 –

The Glue Valves and/or Glue Wheel should be

Disabled

when learning an

Unglued Sample.

Note2 –

The ‘

Learn Wait Timeout

’ can be increased if desired. Click

here

for instructions.

The following steps require boxes of the new order to be passing through the machine

Содержание MCP-8I
































































Результаты поиска

Содержание MCP-8I

Отзывы:

Похожие инструкции для MCP-8I

Бренды по названию

Популярные бренды

VALCO MELTON MCP-8I, Быстрый старт

Результаты поиска

Содержание MCP-8I

Отзывы:

Похожие инструкции для MCP-8I

Бренды по названию

Популярные бренды