VALCO MELTON MCP-8I Скачать руководство пользователя страница 8

Страница: 8 / 63

www.valcomelton.com | TEL: (1) 513-874-6550 | FAX: (1) 513-874-3612

Doc. IS0xxx

Rev.04 | Date: August 25, 2021

MCP-8I Quick Start Guide

Window Display Graphics

Global Jam Setting Input Box

– is used to set the Jam Distance for all Jam Channels

at the same time.

Note –

Each Channel still has to be Enabled and Disabled. Once the

Desired Channels are Enabled, the Global Jam Setting will be transferred.

Figure 10: Jam Global Setting Input Box

Jam Option Text Descriptions

Valve Channel Jam

‘V’ – Indicates Valve Channel

1 – Indicates the Valve Index

‘Scanner 1’ – Indicates the Scanner/Trigger Input Selection.

Figure 11: Valve Jam Prompt

Sensor Channel Jam

‘S’ – Indicates Sensor Channel

‘1’ – Indicates the Sensor Index

‘Int 1’ – Indicates the Scanner/Trigger Input Selection.

Int 1 = Scanner that is connected to Sensor 1 Sensor.

Figure 12: Sensor Jam Prompt

Sync Scanner Jam

Figure 13: Sync Scanner Jam Prompt

Note –

This will only be present when the Sync Scanner is Enabled and the

External Learn is Disabled.

Содержание MCP-8I
































































Результаты поиска

Содержание MCP-8I

Отзывы:

Похожие инструкции для MCP-8I

Бренды по названию

Популярные бренды

VALCO MELTON MCP-8I, Быстрый старт

Результаты поиска

Содержание MCP-8I

Отзывы:

Похожие инструкции для MCP-8I

Бренды по названию

Популярные бренды