Vaillant geoTHERM SERIES Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 132

Vaillant geoTHERM SERIES Скачать руководство пользователя страница 88

Adapting the appliance to the heating system

88

Installation instructions geoTHERM 0020051574_04

9

9.7.4

Menu A: Calling up Installation Assistent

Display shown

Description

Factory setting

Menu A: Calling up Installation Assistent

The Installation Assistent appears automatically when
the heat pump is commissioned. You are guided
through the first two menus A1 and A2.
You now have the opportunity to subsequently
change the settings once more.

Installationsassistent

A1

Sprache

>DE deutsch

Standort

>DE

>Sprache wählen

During the initial installation the controller always
starts with this menu (Installation Assistent).

Sprache (Language):

Set the local language

Standort (Location):

(only when a VPM S solar

charging station is installed) By inputting a loca-
tion in the form of a country code, e.g. DE, and
using the time of day established by a DCF
receiver, an internal sun calendar in the solar
station calculates the times of sunrise and sun-
set. Testing the collector temperature by switch-
ing on the solar pump in 10 minute intervals is
suspended at night-time.

Installation Assistent

A2

Appliance Code

5

Hydraulic scheme

6

Electric Wiring Diagram

1

Accept change

YES

>Select

The hydraulic and wiring systems must be adjusted by
the installer during commissioning.

i

The Appliance Code has already been set

in the factory and must not be changed.
After resetting to factory settings, you
must re-input the value, where required.

Appliance Code:

Type Designation
11

VWS

220/2

12

VWS 300/2

13

VWS 380/2

14

VWS 460/2

23

VWW 220/2

24

VWW 300/2

25

VWW 380/2

26

VWW 460/2

9.9

Menu A: Calling up Installation Assistent

«
...
86
87
88
89
90
...
»

Содержание geoTHERM SERIES





































































































































Отзывы:

Нет отзывов