Vaillant geoTHERM SERIES Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 132

Vaillant geoTHERM SERIES Скачать руководство пользователя страница 4

Notes on the documentation

4

Installation instructions geoTHERM 0020051574_04

1

1

Notes on the documentation

The following instructions are intended to guide you
through the entire documentation. Other documents are
valid in connection with these installation instructions.
We accept no liability for any damage caused by failure to
observe these instructions.

1.1

Observing other applicable documents

>

When installing the heat pump, you must observe all
installation instructions for parts and components of the
heating installation. These installation instructions are
included with the individual parts of the heating installa-
tion and any supplementary components.
You must also observe all operating instructions that
accompany the components of the heating installation.

1.2 Document

storage

>

Pass these installation instructions and all other applica-
ble documents and, if necessary, any required tools to
the system operator. The system operator will be respon-
sible for storing them so that the instructions and tools
are available when required.

1.3

Symbols used

The symbols used in the manual are explained below. Dan-
ger symbols for identifying dangers are also used in this
manual (

¬

Ch. 2.1.1

).

i

Symbol denoting additional useful tips and
information

>

Symbol for a required task

1.4

Applicability of the instructions

These installation instructions apply only for heat pumps
that have the following article numbers:

Type name

Article number

Brine-Water Heat Pumps (VWS)

VWS 220/2

0010002797

VWS 300/2

0010002798

VWS 380/2

0010002799

VWS 460/2

0010002800

Water-Water Heat Pumps (VWW)

VWW 220/2

0010002801

VWW 300/2

0010002802

VWW 380/2

0010002803

VWW 460/2

0010002804

1.1

Type designations and article numbers

The 10-digit article number for the heat pump (this corre-
sponds to the 10 digits that come after the 7th digit of the
serial number) can be found on the sticker on the heat
pump or on the identification plate (

¬

Ch. 3.1

).

«
...
2
3
4
5
6
...
»

Содержание geoTHERM SERIES





































































































































Отзывы:

Нет отзывов