Vaillant geoTHERM SERIES Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 132

Vaillant geoTHERM SERIES Скачать руководство пользователя страница 82

Adapting the appliance to the heating system

82

Installation instructions geoTHERM 0020051574_04

9

Display shown

Description

Factory setting

Legionella protect.

C9

Parameters

Legionella protect.

OFF

Legionella start

04:00

>Select

Legionella protect.:

OFF/Mo/Tu/We/Th/Fr/Sa/Su

Legionella start:

The time which was set determines

when the legionella protection function starts.

The legionella protection function is carried out by
the auxiliary heating on the preset day of the week, at
the preset time, if the auxiliary heating has been acti-
vated.

For this function, the controller sets the flow target
temperature to 76 °C/74 °C (2 K hysteresis). The
legionella protection function is terminated when the
current flow temperature at the cylinder has reached
73 °C for at least 30 min, or after 90 minutes if 73 °C
is not reached (e.g. if hot water is drawn during this
period).

The processes of the legionella protection function
start in a connected drinking water station VPM W.

OFF

04:00

Pump control

C10

Parameters

Circulation pump

100 %

>Select

Circulation pump:

The setting range 1 - 100% is not a

setting for the pump output, but is a division of
time periods relating to an interval of 10 min.,
e.g. 80% = 8 min. operation, 2 min. break.
The time period is active. In this time period, the
circulation pump clocks in accordance with the
set percentage value. The circulation pump does
not start if the DHW cylinder is still too cold.

Recommended settings for systems with VPS/2

¬ Planning information

.

100 %

Solar tank

C11

Parameters

Maximum flow temp.

95 °C

>Select temperature

This menu only appears if a solar tank is installed, e.g.
VPS /2

Maximum flow temp.:

If sufficient solar energy is

available, a connected buffer tank VPS /2 is
heated beyond the target temperatures for
heating and hot water to the maximum tempera-
ture set here.

i

The heating circuits connected to the

buffer tank must be mixed circuits.

9.6. Menu C: Set parameters for the heating system

«
...
80
81
82
83
84
...
»

Содержание geoTHERM SERIES





































































































































Отзывы:

Нет отзывов