manualshive.com logo in svg

Vaillant geoTHERM SERIES, Руководство по установке, Страница: 34 / 132

Поделиться
Скачать
Vaillant geoTHERM SERIES Скачать руководство пользователя страница 34

Hydraulics installation

34

Installation instructions geoTHERM 0020051574_04

5

5.6  

Fitting the flexible connecting hoses

b

 Caution!

Risk of damage caused by leaks.

If the seals with metal support rings are not 
used on the connections for the brine cir-
cuit/well water circuit (

3

) and (

4

) 

(

¬

 Fig. 

 

5.8

)

, this may lead to leaks.

 

>

Ensure that you use the correct seals on 
the connections.

 

– The pipes must be installed and the seals must be used 

in accordance with (

¬

 Fig. 

 

5.8

)

.

 

– The installation must be carried out by a qualified heat-

ing engineer.

 

>

During the installation, observe the applicable regula-
tions.

b

 Caution!

Risk of impaired function.

Air in the heating system leads to impaired 
operation and reduces the heating output. 

 

>

Fit bleed valves as required.

1

5.7  Removing the blind caps

 

>

Remove the blind caps (

1

) from the unit’s connections. 

These are no longer required and can be properly dis-
posed of.

1

2

3

4

5.8  

 Fitting the flexible connecting hoses

Key

1 Heating 

flow

2 Heating 

return 

3  From the heat source to the heat pump
4  From the heat pump to the heat source

 

>

Fit two of the supplied flexible connecting hoses that 
have the yellow/green flat seals (from the fittings pack) 
to the heating circuit connections (

1

 and 

2

).

 

>

Fit two of the supplied flexible connecting hoses that 
have the seals with metal support rings (from the fittings 
pack) to the brine/well water circuit connections (

3

 and 

4

).

Содержание geoTHERM SERIES





































































































































Отзывы:

Нет отзывов