background image

27

PA

R

T 1 CONCENTRIC 60/100

• Unlock the catch between the

terminal and the flue duct by
twisting them against each other
(fig. 4.5).

• Pull the terminal out of the flue

duct.

• Push the variable terminal onto the

flue duct.

Please note: The catch on the top
of the variable terminal must lock
firmly into the notch in the flue
duct (fig. 4.6).

Caution!

Make sure the seal fits tightly.

• Push the flue duct and the variable

terminal back into the air duct
and lock the two catches
(fig. 4.7).

Please note: The seam of the air
duct must be at the top.

• Fit the horizontal ait/flue duct as

described on pages 18 and 21.

Caution!

It cannot be fitted from inside.

• Fit the rest of the variable

termination kit as described on
page 28.

INSTALLATION OF THE VARIABLE TERMINATION KIT

Fig. 4.7:  Locking the catch

Fig. 4.6:  Flue pipe

Fig. 4.5:  Unlocking the catch

Assembly
After installing the flue
duct

Danger!

Before starting work, shut down the
appliance and prevent it from being
switched on unintentionally.

• Remove the wall seal from the

terminal.

• Use an 8 mm screwdriver to bend

the catches inwards (fig. 4.3).

• Pull the terminal with the flue duct

out of the air duct (fig. 4.4).

Caution!

Do not twist the flue duct, because
this might detach the following flue
duct behind the terminal from the
spacer.
• Unlock the catch between the

terminal and the flue duct by
twisting them against each other
(fig. 4.5).

• Pull the terminal out of the flue

duct.

• Push the new variable terminal

onto the flue duct.

Please note: The catch on the top
of the variable terminal must lock
firmly into the notch in the flue
duct (fig. 4.6).

Please note: Make sure the seal
fits tightly.

• Push the flue duct with the

variable terminal back in the air
duct. Carefully push the flue duct
back into the sleeve of the duct or
bend behind it. Lock the two
catches (fig. 4.7).

• Fit the wall seal on the variable

terminal.

• Fit the rest of the VTK as

described on page 28.

834449_05GB_022005.qxd  02.02.2005 17:12 Uhr  Seite 27

Содержание ecoMAX 618/2 E





























































Отзывы: