Vaderstad RAPID RDA S Series Скачать руководство пользователя | Manualshive

Страница: 88 / 122

background image

Maintenance and service

88

Ver.2 01.11.2002

5.21.3

Draining condensing water

Prior to first use each season or following extended interruption, be sure to drain condensing water
from the tank.

!

Park the machine on an inclination to have the tank inclined towards the drain connector at its
bottom.

!

Put a vessel under the cock (C) and open it. Keep the cock open until clean oil comes out. Then
close the cock. If necessary, fill up with oil.

Starting after filling up oil or replacing the filter and oil:

When filling up or replacing the oil, air will mix with the oil in the tank. This air must be removed
prior to operation of the system since it could cause damage to the pump and pump motor.

!

Start the fan with the tractor at idle.

!

Listen to the fan and wait until it operates smoothly.

!

If air bubbles are visible in the inspection window, allow the fan to run another while at idle
speed.

!

Increase the fan rpm to approx. 3000 rpm.

!

Listen to the fan and wait until it operates smoothly.

!

The fan should now be operated at normal operating speed.

5.22 Intermediate packer (option)

Figure 5.32

NOTE!

Never stand under the intermediate packer or drill if it is suspended and only secured with

the tractor's hydraulic lifting arms. Prior to any service on the intermediate packer, be sure to se-
cure it properly with trestles, etc. on firm, level ground.

!

Lubricate the intermediate packer every 100 hectares.

!

Retighten the bolt joints on the intermediate packer at the end of every season.

«
...
86
87
88
89
90
...
»

Содержание RAPID RDA S Series



























































































































Отзывы:

Нет отзывов

Похожие инструкции для RAPID RDA S Series

Бренд: Yard Machines Страницы: 16

Бренд: York Страницы: 212

Бренд: Poulan Pro Страницы: 28

Бренд: Cramer Страницы: 48

Бренд: AIREDALE Страницы: 218

Бренд: Troy-Bilt Страницы: 28

Бренд: Haden Страницы: 16

Бренд: Iom Страницы: 49

Бренд: Fort Страницы: 36

Бренд: Troy-Bilt Страницы: 16

Бренд: Troy-Bilt Страницы: 40

PERFORMA MPE Series

Бренд: Galletti Страницы: 48

Бренд: Daikin Страницы: 130

Бренд: York Страницы: 188

Бренд: York Страницы: 268

Бренд: Daikin Страницы: 84

Бренд: Laird Страницы: 11

Nextreme NRC400

Бренд: Laird Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды