Vaderstad RAPID RDA S Series Скачать руководство пользователя

Страница: 80 / 122

Maintenance and service

Ver.2 01.11.2002

5.8

Lubrication points

Be safety conscious and do not crawl under the drill to lubricate. Lubricate from above, or support
the drill securely on trestles. See

”1 Safety regulations” on page 8.

Lubricate regularly as shown below: the disc bearings should be greased until grease appears or
by 2-3 strokes of the grease gun.

The lubrication chart with picture references can be found in the Spare Parts list.

Grease into all grease nipples at the intervals specified and always after pressure washing the drill.

Never direct water onto a bearing. It is easy to spoil seals and ball bearings with a pressure washer
since water can be forced into the bearing and cause rusting.

Lubricate at the end of each season.

5.9

Changing discs

Make sure that the drill is securely supported on trestles.

When changing discs, use a ratchet spanner or preferably a nut runner. Turn the disc so that the
completely flat side faces the seed coulter.

NOTE!

The discs have sharp edges, so wear gloves!

Adjust the coulter if necessary, see

”3.25 Adjusting the seed coulters” on page 66.

Table 5.1 Lubrication points and intervals

Lubrication inter-
val

Number

Lubrication points

100 ha

500 ha/

season

500/600/800

Transmission joint

Drive wheel suspension

Drive wheel chain

Hinges on centre/wing sections and wheel beam pivots X

5/7/9

RDA 500 S marker mountings, markers

RDA 600-800 S marker mountings, markers

Master ram head

Disc bearings

40/48/64

Wheel hub

20/24/32

Wheel fork

20/24/32

Hydraulic feed output chain

Oil filter replacement (hydraulic feed output)

Intermediate packer (option)

Содержание RAPID RDA S Series



























































































































Результаты поиска

Содержание RAPID RDA S Series

Отзывы:

Похожие инструкции для RAPID RDA S Series

Бренды по названию

Популярные бренды

Vaderstad RAPID RDA S Series, Инструкция по эксплуатации

Результаты поиска

Содержание RAPID RDA S Series

Отзывы:

Похожие инструкции для RAPID RDA S Series

Бренды по названию

Популярные бренды