Vaderstad RAPID RDA S Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 122

background image

Safety regulations

10

Ver.2 01.11.2002

1.3

Other safety precautions

!

Observe the greatest caution when transporting the drill on a public road. When driving with a
full hopper, remember that the following weight is great and that the view to the rear is very
restricted. Check the position of the tractor rearview mirrors. If the machine is to be transported
over a longer distance, be sure to block the lifting ram of the centre section with the yellow
mechanical locking device.The owner/operator is solely responsible for transport of the seed
drill on public roads. Use the lights on the drill according to the local traffic regulations.

!

NOTE!

This machine and its tyres are designed for a maximum speed of 30 km/h on the road.

!

During service or repair work on the hydraulic system, the wing sections must be lowered and
the drill must be in the lowered position and resting on a firm surface.

!

Never stand under the intermediate packer or drill if it is suspended and only secured with the
tractor's hydraulic lifting arms. Prior to any service on the intermediate packer, be sure to se-
cure it properly with trestles, etc. on firm, level ground.

!

Before service or repair work on the weight transfer hydraulic system, the accumulators must
be drained of oil. See

5.15 Bleeding the hydraulic system accumulators” on page 84

.

!

Be sure to set the master cylinder stopper in such a way that the drill rests on both the wheels
and the discs when parked. Since the pressure on the supporting leg is great, the machine shall
not be parked on loose surfaces.

!

Always ensure that the male coupling of the drill and the female coupling on the tractor are
clean before connecting.

!

Always use Väderstad original spare parts to maintain the quality and reliability of the seed
drill. If other makes of spare parts are used, all guarantee and claims commitments cease to be
valid.

!

Regularly inspect the wear on the drill's towing eyelet. Replace the towing eyelet when it has
been worn down to the wear limit. See ”

3.2 Inspecting the drill's towing eyelet” on page 24

!

Any welding work on the machine/implement should hold professional standard.

Incorrect welding may result in serious injuries or possibly fatal injuries. If in doubt, contact a
professional welding service for proper instructions.

!

Never look straight into the optics of the radar when it is operating! There is a risk of permanent
damage to the eyesight! (Hydraulic feed output).

1.4

Location of warning decals on the machine

Figure 1.3

B,D,F,I,J,K,M

E

D

D

C

C

G

H, L

C

D

«
...
8
9
10
11
12
...
»

Содержание RAPID RDA S Series



























































































































Отзывы:

Нет отзывов

Похожие инструкции для RAPID RDA S Series

Бренд: ICEMASTER Страницы: 5

Бренд: Daikin Страницы: 12

MILLENNIUM YT J

Бренд: York Страницы: 16

Бренд: Garland Страницы: 184

Бренд: Poulan Pro Страницы: 28

Бренд: Echo Страницы: 24

Бренд: Hitachi Страницы: 140

Бренд: Tar River Страницы: 45

Бренд: Powermate Страницы: 48

Бренд: Sentar Страницы: 60

Бренд: Sandr Garden Страницы: 64

Бренд: Zanotti Страницы: 32

Бренд: Häfele Страницы: 11

Бренд: hailea Страницы: 15

Бренд: Rally Страницы: 60

Бренд: Quantech Страницы: 188

Бренд: Daikin Страницы: 25

ARENA-VATOR III AV3-4

Бренд: Gearmore Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды