USAutomation Accuriss 57 Series Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 103

background image

USA57 Revision

1.2

92

Notes On Feedback Mode



If motor consistently stops during a move:

If a very fine line count encoder is used such that, for example, the encoder ratio is around
2000, or if the encoder is decoupled from the motor shaft, or if the encoder ratio has some
fractional component and is non integer, increase the error (

aC

) allowed for the coarse

algorithm. For example set

aC

to

2000

. This way a move that is in progress will not be halted

and restarted because the coarse algorithm has detected that the following error is too large.
Instead, the move will complete with some error, and the fine algorithm integrator will null out
the error to within the lower case “

ac

” value at the end of the move.



Busy/Non Busy Status:

The status will read busy until any move is reached to within the “ac” value; however, once a
move is complete any subsequent disturbance is handled by the fine integrator as long as it is
less than “aC” (upper-case C). These subsequent corrections by the fine algorithm will not
read busy; however, if the error becomes greater than “aC” the deadband reckoning algorithm
is turned on, and a formal correction move is initiated. This move changes the drive status to
busy, and no external commands will then be accepted. It is important to set the coarse
deadband reckoning (aC value) to a reasonable number (for example, 50) or else the drive will
always be attempting to correct.

Other Notes



When position correction mode is enabled (

/1n8R

) the drive will keep retrying any stalled

moves until the number of “

au

” retries are exhausted, and will NOT halt any strings or loops

upon detection of a stall.



During position correction mode, the “

/1T”

command

will halt any move, but there is a

possibility that the drive may instantly reissue itself a position correction command, especially
if it is fighting a constant disturbance. It may be necessary to issue a “

/1n0R”

command

to

positively halt a move in progress.



If the encoder ratio is changed from its default of 1000, the allowed max position will be

decreased from +2,147,483,648 by the same ratio. The max position counter will rollover from
positive to negative range when this limit is exceeded.



Do not use the upper case “

F

” (reverse direction) command when using encoder feedback

mode. Instead, switch the encoder AB lines or the lead wires to one phase of the motor.



Jog mode will not work with encoder feedback on

Arbitrary Measurement Units

It is not necessary to use feedback mode or even have an encoder, in order to set the encoder
ratio

/1aE32000R

etc. Setting the encoder ratio thus allows positioning in any units of the user’s

choice.

«
...
90
91
92
93
94
...
»

Содержание Accuriss 57 Series








































































































Отзывы:

Нет отзывов

Похожие инструкции для Accuriss 57 Series

Бренд: Paratec Страницы: 8

Бренд: J+J Страницы: 33

Бренд: Samson Страницы: 32

Бренд: Quantum Страницы: 15

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 19

Бренд: X Rocker Страницы: 38

Liquitron DP5000-01A

Бренд: LMI Technologies Страницы: 28

Бренд: Motrona Страницы: 10

PSS67 IO1 16FDI

Бренд: Pilz Страницы: 36

Бренд: Watlow Страницы: 20

Бренд: W.E.ST. Страницы: 34

Бренд: Ltech Страницы: 4

Бренд: Motor Guard Страницы: 2

Бренд: K&K Страницы: 6

Бренд: Vent-Axia Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды