USAutomatic SENTRY 300 D Скачать руководство пользователя | Manualshive

Страница: 28 / 48

background image

27

17. Cut extension cable to length allowing for future considerations.
18. Remove 2” of cable insulation to expose the 5 wires.

Caution: do not damage internal wires.

19. Remove approximately 1/2” of insulation from each wire.
20. Locate 8 pin connector and pigtail previously cut from Gate 2 linear

actuator cable. Prepare wires for the splice.

21. Connect the 5 wires from extension cable to the 5 wires from the pigtail

by matching the wire colors. Then secure with supplied wire nuts.

22. Roll cable and place in wire compartment.
23. Install junction box cover and securely snap in place.

Connecting Gate 2 Linear Actuator to Control Board

1. Locate the power connector attached to the linear actuator cable (red and black wires).
2. Connect it to the remaining Plug N Go harness linear actuator power plug. These connectors are

designed so that incorrect connection is not possible and it does not matter which connector is

used.

3. Locate the linear actuator cable 8 pin plug. Connect it to the Gate 2 connector located on

the Sentry Control board adjacent to the Gate 1 connector. Securely snap in place. Once all

connections are made place wires in wire compartment.

Preparing to Operate Gate 2 for the First Time

Using the “Open/Close Command” button on the control board open Gate 1. This is done because

Gate 2 was just installed in the open position and now both gates should be in the open position.

Operating Gate 2 for the first time and final adjustments

1.  Locate the control switches and turn on switch 4 (press down on the right side).
2.  Gate 1 and Gate 2 should be in the open position if installed correctly.
3.  Press the “Open/Close Command” button to close Gate 1 and Gate 2.
4.  Gate 2 limit adjustment has not been made so it should stop short of fully closed.
5.  Turn “OFF” control switch 3, disabling Gate 1.
6.  Now use the “Open/Close Command” button to cycle Gate 2 and adjust Gate 2 close limit

to match Gate 1 close position.

7. With both gates now closed, turn “ON” control switch 3 enabling Gate 1.
8. Press “Open/Close Command” to open both gates and then close, adjust limit positions if

necessary.

CAUTION:

To reduce the risk of injury, USAutomatic strongly recommends the installation of

additional safety devices such as Photo Eye Sensors and Safety Edges. Consult an authorized

installing dealer or www.Sentrygateopener.com for a complete explanation of options and see

the Safety Section of this manual on pages 3 to 4.

«
...
26
27
28
29
30
...
»

Содержание SENTRY 300 D

















































Отзывы:

Нет отзывов

Похожие инструкции для SENTRY 300 D

Бренд: tau Страницы: 40

Бренд: La Toulousaine Страницы: 6

Бренд: CAME Страницы: 28

Бренд: White Rose Страницы: 29

ThermoMark 5150

Бренд: Wayne-Dalton Страницы: 4

Бренд: Cardin Elettronica Страницы: 44

Бренд: Micanan Страницы: 44

Бренд: Calimet Страницы: 24

Бренд: Microbrain Intelligent Technology Страницы: 32

Бренд: Waring Страницы: 5

Бренд: Alutech Страницы: 3

Бренд: Alutech Страницы: 12

Panelift B&D Storm-Shield PFI

Бренд: B&D Страницы: 32

Бренд: USAut Страницы: 68

Бренд: Rival Страницы: 12

Бренд: CAME Страницы: 32

Бренд: Hamilton Beach Страницы: 5

Бренд: vds Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды