USAutomatic SENTRY 300 D Скачать руководство пользователя

Страница: 39 / 48

6. Single or dual gate

installation gate auto

opens instead of auto

closing

1. In this condition the open time can be controlled by adjusting

the auto close timer adjustment.

2. If installed in the pull to open configuration then control switch

number 2 should be turned “OFF” verify it is. If installed in the

push to open configuration verify switch is turned “ON”.

3. Gate is trying to close too far. Readjust close limit adjust for

gate 1 or gate 2 to the correct stop position.

4. If time before auto opening cannot be adjusted and occurs

in a couple of seconds after closing then the close limit

adjustment of one or both gates is misadjusted. The feature

that is causing the gate to open is the current sense circuit

on the control board. The gate is trying to close farther than

possible and it has traveled to the full extent of the linear

actuator. Verify that linear actuator harness has no cuts or

nicks.

5. Verify correct installation of the universal actuator bracket.

Possible cause is incorrect installation of the gate bracket or

linear actuator bracket. Verify and correct as required.

7. Gate begins to open or

close and stops and

reverses after a couple

of seconds

1. This occurs when the sensitivity circuit on the control board

senses an obstruction. Verify that the gate is not obstructed

by some object at the point where it reverses. Could also be

due to hinges binding or gate contacting ground.

2. This is an adjustable feature and the cause could simply be

an adjustment of the Gate 1 or Gate 2 sensitivity. Turn the

sensitivity adjustment toward a minimum setting and always

set the Gate 1 and Gate 2 adjustment to the same setting on

a single gate installation. In dual gate installation adjust both

as necessary.

8. Pressing the “RESET”

button only, causes the

gate to operate (open,

close and stop) acts like

transmitter.

1. This problem is probably due to a bad receiver.
2. To isolate this disconnect the J3 connector from the control

board.

3. With J3 disconnected see if Reset button causes gate to

operate. If gate no longer operates when Reset is pressed

then the receiver was the cause.

4. Connect J3 back to Sentry control board and see if problem

returns. If problem returns then the receiver is bad.

Содержание SENTRY 300 D
















































Результаты поиска

Содержание SENTRY 300 D

Отзывы:

Похожие инструкции для SENTRY 300 D

Бренды по названию

Популярные бренды

USAutomatic SENTRY 300 D, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SENTRY 300 D

Отзывы:

Похожие инструкции для SENTRY 300 D

Бренды по названию

Популярные бренды