USAutomatic SENTRY 300 D страница 35 Скачать руководство пользователя

Страница: 35 / 48

Terms and Definitions

Control board -

See page 19

Receiver

- See page 22

Transmitter

- Hand held unit with 2 buttons, used to operate the gate, sends signal to receiver when

button is pressed see page 22.

Linear Actuator

- Connected to gate and hinge post, contains the motor, gearbox.

Connector

- Control board has Six, two white 8-pin connectors (X1 and X2) are used to connect linear

actuator to control board and one 7-pin connector (J2) (located bottom center of control board) for

accessory wiring, two 2 pin header (J3, J4) for entrapment siren & external “Reset” and one four

pin header (J1) for receiver.

Push Button

- Two are located on the control board. “Open/Close command” used to operate the gate

and the “Reset” used to reset the control board after current sensing twice before a limit is

reached see page 21.

Control Switches

- Used to turn “ON” or “OFF” specific control board functions see page 21.

Sensitivity adjustments

- Located on the control board see page 19. These adjustments are

the primary safety feature. If the gate comes in contact with an object it will stop and reverse.

These adjustments control the amount of force applied to an object before reversing the gate.

Charge Controller

- Located inside the control box see page 17. This is the battery charger.

The input power for this device can be either from the transformer (supplied) or the Sentry Solar

Panel (Part #520015).

Transformer

- This device connects to a 110 VAC electrical outlet and converts it to a low AC voltage that

can be connected to the charge controller to provide continuous charging of the battery.

Retract and Extend Limit

- This refers to the fully open or closed position and are adjusted on the control

board see page 20.

Entrapment Siren

- If the control board sensitivity circuit senses an obstruction it will reverse the gate

and if a second obstruction is detected before the gate reaches a fully open or close limit the

control board will shut down the opener and sound the entrapment alarm for five minutes or until

the “Reset” button is pressed.

Gate 2 -

is defined as the gat e on the other side of the drive from the control box.

Troubleshooting

Содержание SENTRY 300 D
















































Результаты поиска

Содержание SENTRY 300 D

Отзывы:

Похожие инструкции для SENTRY 300 D

Бренды по названию

Популярные бренды

USAutomatic SENTRY 300 D, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SENTRY 300 D

Отзывы:

Похожие инструкции для SENTRY 300 D

Бренды по названию

Популярные бренды