US Robotics Courier USR3510 Скачать руководство пользователя страница 96

Страница: 96 / 162

Revision: 1.00

96 |

P a g e

WAN/LAN Switchover Feature

The WAN/LAN switchover feature defines the state of the Ethernet port at power-on. By default, this
feature is enabled. Learn how to

disable WAN/LAN Switchover.

Two modes are possible:



WAN mode: the Ethernet interface act as a WAN interface



LAN mode: the Ethernet interface acts as a LAN interface

Each time the unit is powered on:



Gateway sends a DHCP discover message over the Ethernet interface.



When it receives a DHCP offer it proceeds with the DHCP protocol and the Ethernet interface
remains in WAN state.



When it does not receive a DHCP offer it resends the DHCP discover message five times. If no DHCP
offer is received after five tries, the gateway starts running a DHCP server on the Ethernet interface
and act as a LAN interface.

TIP:

WAN/LAN detection only happens during power on. The Ethernet connection remains in the same

state (WAN or LAN) until a power cycle or reset has happened.

Содержание Courier USR3510





























































































































































Результаты поиска

Содержание Courier USR3510

Отзывы:

Похожие инструкции для Courier USR3510

Бренды по названию

Популярные бренды

US Robotics Courier USR3510, Руководство пользователя

Результаты поиска

Содержание Courier USR3510

Отзывы:

Похожие инструкции для Courier USR3510

Бренды по названию

Популярные бренды